Advantech B+B SmartWorx iMcV-LIM User Manual Download Page 17

iMcV-LIM 

 

17 

 

 

B+B SMARTWORX TECHNICAL SUPPORT 

 
USA/Canada: 

1 (800) 346-3119 (Ottawa IL USA)

 

Europe: 

+353 91 792444 (Ireland / Europe)

  

Email: 

[email protected]

 

Web: 

www.advantech-bb.com

 

 

 

 

STATEMENTS,  PRECAUTIONS,  GUIDELINES,  REGULATORY 

 

FCC  RADIO  FREQUENCY  INTERFERENCE  STATEMENT 

This equipment has been tested and found to comply with the limits for a 

Class A computing device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference 

when the equipment is operated in a commercial environment. This equipment 

generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a 

residential area is likely to cause harmful interference in which the user will be 

required to correct the interference at his own expense. 
Any changes or modifications not expressly approved by the manufacturer 

could void the user’s authority to operate the equipment. 
The use of non-shielded I/O cables may not guarantee compliance with FCC 

RFI limits. This digital apparatus does not exceed the Class A limits for radio 

noise emission from digital apparatus set out in the Radio Interference 

Regulation of the Canadian Department of Communications. 
Le présent appareil numérique n’émet pas de bruits radioélectriques 

dépassant les limites applicables aux appareils numériques de classe A 

prescrites dans le Règlement sur le brouillage radioélectrique publié par le 

ministère des Communications du Canada. 

 

 

Summary of Contents for B+B SmartWorx iMcV-LIM




















Reviews: