manualshive.com logo in svg

Advantech Wireless SSPBMg-C400-BRE, Installation And Operating Manual, Page: 23 / 46

Share
Download
Advantech Wireless SSPBMg-C400-BRE Installation And Operating Manual Download Page 23

 

   

 

 

   

 

 

 

   

SSPBMg-C400-BRE

 

4.2 REDUNDANT INTERFACE 

 
The

 Redundant Interface 

connections are made with a 10-pin circular connector mounted on 

the SSPB enclosure.  The connector type is listed in 

TABLE 5

 at page 17 and the location is 

shown in 

Figure 4

 at page 16.  A redundant system cable is provided with the redundancy kit 

that provides the interconnection between the two SSPB units and the waveguide switch in a 
redundant configuration. 
 
This interface is not used for standalone units. 

 

 

4.3 LED 

 

TX

: green/red LED indicating the state of the transmission path. 

• 

If this LED is not lit, the unit is not powered (or the power supply failed). 

• 

If this LED is RED lit, it indicates that the unit is in FAULT or ALARM condition. 

• 

If this LED is blinking GREEN, it indicates that the unit is in MUTE state (following a 
MUTE command). 

• 

If this LED is GREEN lit, it indicates that the unit is functioning properly. 

 
 
 

4.4  RF OUTPUT MONITOR INTERFACE  

 
This RF output sample port is located at the RF MON connector, which is mounted on the SSPB 
enclosure. The type of mounting connector is listed in 

TABLE 5

 at page 17 and the location is 

shown in 

Figure 4

 at page 16.  This interface is used for the independent monitoring of the SSPB 

output.

  

A table of the coupling factor versus the frequency is provided with each unit. Note that 

because this port is located before the band-pass filter (BPF) the signal on this port may contain 
spurious signals and harmonics. This port should only be used for output power monitoring (via 
an external power meter) or should be kept capped if not used.  
 

        Page 

 

22

Summary of Contents for SSPBMg-C400-BRE















































Reviews:

No comments