Advantech Wireless SSPBMg-C400-BRE Installation And Operating Manual Download Page 2 | Manualshive

Page: 2 / 46

Advantech Wireless SSPBMg-C400-BRE Installation And Operating Manual Download Page 2

SSPBMg-C400-BRE

WARRANTY

This Advantech Wireless product is warranted against defects in material and workmanship for a
period of 2 years from date of shipment. During the warranty period, Advantech Wireless will, at
its option, either repair or replace products that will prove to be defective.

To return a product for warranty or repair service, you must first request a Return Material
Authorization (RMA) number by contacting Advantech Wireless at:

Phone: (514) 420-0045

or

Fax: (514) 420-0073

www.advantechwireless.com

or

e-mail: [email protected]

The unit should be shipped to the following address, in original shipping container (box), with
shipping charges prepaid.

Advantech

Wireless

657

Orly

Avenue

Dorval,

Quebec

H9P

1G1

CANADA

Please indicate the RMA number on all shipping documentation.

Units shipped without prior issued RMA, or shipped not in original packing, may be subject of
rejection and returned at sender’s own expense.

LIMITATIONS OF WARRANTY

Advantech Wireless warrants this product to be free of materials and workmanship defects.

The foregoing warranty shall not apply to defects resulting from improper handling or abuse by
the Buyer, unauthorized modification, operation outside of the environmental specifications for
the product, or improper installation or maintenance.

Advantech Wireless shall not be liable for any direct, indirect, special, incidental or
consequential damages.

Page

1

«
1
2
3
4
...
»

Summary of Contents for SSPBMg-C400-BRE















































Reviews:

No comments