Advansus LM5560-Q45 User Manual Download Page 35

Page: 35 / 79

User’s Manual

LM5560-Q45

Label

Function

Description

AUDIO1

Line-Out port (Lime)

This port connects a headphone or a
speaker. In 4-channel, 6-channel, and
8-channel configuration, the function of this
port becomes Front Speaker Out.

AUDIO1

Microphone port (Pink)

This port connects a microphone.

LAN_USB12

USB 2.0 connector

These two 4-pin Universal Serial Bus (USB)
ports are available for connecting USB 2.0
devices.

USB34

USB 2.0 connector

These two 4-pin Universal Serial Bus (USB)
ports are available for connecting USB 2.0
devices.

VGA1

VGA port

This 15-pin port is for a VGA monitor or
other VGA-compatible devices.

COM1

Serial port connector

D-Sub 9-pin, male

KBMS1

PS/2 KB connector

This port is for a PS/2 keyboard

Summary of Contents for LM5560-Q45
















































































Search results

Summary of Contents for LM5560-Q45

Reviews:

Related manuals for LM5560-Q45

Brands by name

Popular brands

Advansus LM5560-Q45, User Manual

Search results

Summary of Contents for LM5560-Q45

Reviews:

Related manuals for LM5560-Q45

Brands by name

Popular brands