background image

70

 - FORM NO. 56043103 - Warrior

™ 

ST, Warrior

 AXP

ELECTRICAL SYSTEM
MAIN CONTROL PROGRAMMING OPTIONS (CONTINUED)

Regular Scrub Setting Adjustment:

FACTORY DEFAULT: SCRUB PRESSURE =1, SOLUTION = ONE BAR(#1), CHEMICAL = 0 (IF AVAILABLE).

The regular scrub pressure, solution rate and chemical rate can be programmed depending on its application where high solution rate is need with regular scrub 
pressure or low solution rate with heavy scrub pressure.  To change scrub pressure setting, solution rate setting and chemical setting, perform the following steps:

AXP™ models:

Turn the main power key switch to the off position.

Press and hold the scrub on and the wand switch.

While holding both switches, turn the main power key switch to the on position.

Continue to hold the both switches until the wand indicator and regular scrub indicator turn green.

Release both switches.  The display will now show the cylinder deck icon with current scrub pressure setting.  Scrub off indicator will turn red and regular scrub 
indicator will turn yellow.

Pressing scrub on switch will now select new scrub pressure.  Pressing scrub off switch will save the new setting and move to solution rate setting.

The display will now show solution icon with gauge.  The regular scrub indicator will now turn green and solution indicator will turn yellow.  Pressing solution 
switch will now select new solution rate.  Pressing scrub off switch will save the new setting and move to chemical setting (If available).

The display will now show chemical bottle with current chemical setting.  Solution indicator will turn green and chemical indicator will turn green.  Pressing 
chemical switch will now select new chemical setting.  Pressing scrub off switch will save the new setting and display key switch icon on display.

Turn the main power key switch to the off position.

10  The new settings will be saved and will remain in effect until they are changed again.

ST models:

Turn the main power key switch to the off position.

Press and hold the scrub on and the wand switch.

While holding both switches, turn the main power key switch to the on position.

Continue to hold both switches until the wand indicator and the regular scrub indicator turn green.

Release both switches.  The LED display will show the number of the current scrub pressure setting, the scrub off indicator will turn red and the regular scrub 
indicator will turn yellow.

Press the scrub on switch to select the new scrub pressure.

Press the scrub off switch to save the new scrub pressure setting and move to the solution rate setting.  The solution 

fl

 ow indicator will display the number of 

bars corresponding to the current solution 

fl

 ow setting, the regular scrub indicator will turn green and solution indicator will turn yellow.

8.  Press the solution switch to select new solution 

fl

 ow rate.

Press the scrub off switch to save the new setting.  The scrub off indicator will turn green.

10  Turn the main power key switch to the off position.  The new settings will be saved and will remain in effect until they are changed again.

SCRUB PRESSURE & CURRENT LOAD (AMPS) SPECIFICATIONS CHART

Scrub Mode

Scrub Pressure 

Indicator

DECK TYPE

Disc 28”

Cyl. 28”

Disc 32”

Cyl. 32”

Regular Scrub

1 bar(#1)

14 AMPS

22 AMPS

16 AMPS

24 AMPS

Heavy Scrub

2 bars(#2)

22 AMPS

31 AMPS

24 AMPS

33 AMPS

Extreme Scrub

3 bars(#3)

36 AMPS

40 AMPS

38 AMPS

42 AMPS

SOLUTION FLOW RATE CHART

Solution Flow Indicator

Flow Rate

One bar gauge(#1)

.3 g/m

Two bar gauge(#2)

.6 g/m

Three bar gauge(#3)

.9 g/m

CHEMICAL CHART

0

Normal chemical setting

-

10% less than normal chemical setting

+

10% more than normal chemical setting

revised 5/08

Summary of Contents for Warrior AXP























































































Reviews: