background image

FORM NO. 041410 / HYDRO-RETRIEVER 2067 - 

9

____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

1

CHOKE - primes the gasoline engine for cold starting.

2

DUST CONTROL LEVER - controls the vacuum system and the vacuum filter shaker. The vacuum system picks up dust raised by the main
broom. The filter shaker cleans the vacuum filter.

3

THROTTLE CONTROL LEVER (DIESEL) - controls the speed of the engine. When operating the machine, the throttle control lever should be
in the full throttle position.

4

MAIN BROOM LEVER - raises and lowers the main sweeping broom. The sweep position is for smooth floors. The full float position is for rough
floors.

5

HYDRAULIC FILTER LIGHT - indicates when the hydraulic oil filter should be serviced.

6

HYDRAULIC OIL HOT LIGHT - when this light glows, shut down the machine immediately. Allow the machine to cool down, then check for a
problem in the hydraulic system.

7

SCRUB BRUSHES ON/OFF SWITCH - raises (and shuts off) the scrub brushes, or lowers (and starts) the scrub brushes.

8

BROOM MOTORS ON/OFF SWITCH - starts or stops the hydraulic motors that turn the main and side brooms.

9

SQUEEGEE RAISE/LOWER SWITCH - raises and lowers the squeegee. With the rocker switch on, the squeegee is in the automatic mode.
Raising and lowering is controlled by the forward/reverse drive pedal. The squeegee will raise in reverse and lower in forward.

10 SIDE BROOM RAISE/LOWER SWITCH - raises or lowers the side broom.

11 SOLUTION CONTROL LEVER - controls the amount of solution dispensed to the scrub brushes.

12 FUEL GAUGE - indicates the amount of fuel in the gasoline or diesel fuel tank.

13 OIL PRESSURE GAUGE - indicates the engine oil pressure while the engine is running.

14 WATER TEMPERATURE GAUGE - indicates the temperature of the engine coolant while the engine is running.

15 BATTERY METER - indicates the level of battery charge.

16 HOUR METER - indicates the accumulated hours of usage.

17 HOPPER DUMP DOOR SWITCH - opens and closes the hopper dump door.

18 HOPPER RAISE/LOWER SWITCH - controls the hydraulic cylinder that raises the hopper for dumping.

19 KEY IGNITION SWITCH - controls the engine and some parts of the electrical system.

20 THROTTLE CONTROL SWITCH - controls the speed of the engine. When operating the machine, the throttle control switch should be in the

full throttle position (lll).

KNOW YOUR MACHINE

Summary of Contents for Hydro-Retriever 2067





























Reviews: