background image

64

 - FORM NO. 56043098 - Convertamatic

™ 

24C, 24D, 26C, 26D, 28C, 28D

ELECTRICAL SYSTEM
MAIN CONTROL PROGRAMMING OPTIONS (CONTINUED)

Restoring the scrub pressures to factory default settings:

If it is desired to restore the scrub pressures to factory default setting, perform the following steps:

Turn the main power key switch to the off position.

Press and hold the scrub on switch.

While holding the scrub on switch, turn the main power key switch to the on position.

Continue to hold the scrub on switch until the scrub off indicator turns green.

The display will show pressure icon on the right top corner indicating you are in pressure restoring mode.  Now display will show key switch icon asking you to 
reset the machine.

The factory default pressures have now been restored.

Turn the main power key switch to the off position.

Scrub deck type, chemical and recycle option selection:

The CONVERTAMATIC can be equipped with numerous scrub deck options.  This function con

fi

 gures the control unit current settings for each of the scrub deck 

types.  Improper setting of the deck may result in motor damage due to overloading.  Chemical option and recycle option can be selected in this mode.  To select the 
proper scrub deck, chemical option and recycle option:

Turn the main power key switch to the off position.

Press and hold the scrub system off and scrub on switches.

While holding both switches, turn the main key switch to the on position.

Continue to hold both switches until light scrub indicator turns yellow.

Release both switches.  Scrub off indicator will turn red and the display will show the current scrub brush type icon and scrub deck size.  Display will display 
current deck size and type.  (disc or cylindrical, 24”, 26” or 28”).  Chemical option and recycle option can be selected here while selecting scrub deck.

To select chemical option, press chemical switch.  Chemical indicator will turn green.  To deselect chemical option, press chemical switch again.  Chemical 
indicator will turn off.

To select recycle option, press recycle switch.  Recycle indicator will turn green.  To deselect recycle option, press recycle switch again.  Recycle indicator will 
turn off.

The display will display current scrub deck.  There are four selections that can be made.  Pressing the scrub on switch will select between the four settings.  
Scrub on indicator will change every time switch gets pressed.

Select disc icon with 24”, 26” if the machine is equipped with a 24” or 26” disc deck.  Select cylindrical icon with 24”, 26” if the machine is equipped with a 24” 
or 26” cylindrical deck.  Select disc icon with 28” if the machine is equipped with 28” disc deck.  Select cylindrical icon with 28” if the machine is equipped with 
28” cylindrical deck.

10  Once the proper scrub deck size, chemical option and recycle option are selected, press the scrub off switch to save this setting.
11  The display will display key switch icon asking user to reset the machine.
12  Turn the main power key switch to the off position.

Note: It is very important to set chemical and recycle options properly.  This could result unusual operation of the machine.

Summary of Contents for Convertamatic 24C














































































Reviews: