manualshive.com logo in svg

Advance acoustic Convertamatic 24C, Service Manual

Share
Download
Advance acoustic Convertamatic 24C Service Manual Download Page 38

36

 - FORM NO. 56043098 - Convertamatic

™ 

24C, 24D, 26C, 26D, 28C, 28D

SQUEEGEE SYSTEM
CASTER WHEEL REMOVAL

 WARNING!

Disconnect the battery pack connector before servicing machine.

 WARNING!

Never work under machine without safety stands or blocking to support the machine.

1 

Drain both the solution and recovery tanks.  Remove the squeegee assembly and have the scrub deck in the up (stored) position with the scrub brushes 
installed.

2 

See Figure 4.

  Place Wood Blocking 

(G)

 in front of the drive wheels to prevent the machine from rolling.

3 

Jack the machine in the location shown until the caster wheel is approximately 1” off the ground.

4 Place 

Blocking 

(H)

 under the chassis tab as shown.

5 

Remove the (4) Screws, Nuts & Washers 

(I)

 then remove the Caster Assembly 

(J)

. 

6 

Reinstall in reverse order.

FIGURE 4

Summary of Contents for Convertamatic 24C














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands