6
617111561F1-13A
Initial Switch Configuration Using a Web Browser
After powering up the switch for the first time, you can perform the initial switch configuration using a web browser.
To begin with the initial configuration stage, reconfigure your PC’s IP address and subnet mask to make sure the PC can communicate with the switch. After
changing PC’s IP address (for example, 10.10.10.250), then access the web interface of the switch using the switch’s default IP address as shown below.
To initially configure the switch, complete the following steps.
1. Power up the PC that you will use for the initial configuration. Make sure the PC has the Ethernet RJ-45 connector to be connected to the switch via standard
Ethernet LAN cable. If the switch is connected to a DHCP server, skip to Step 3.
2. Reconfigure the PC’s IP address and subnet mask as below, so that it can communicate with the switch. For example, the method to change the PC’s IP
address for a PC running Windows® 7/8.x/10 is as follows:
a. Type
network and sharing
into the Search box in the Start menu.
b. Select
Network and Sharing Center
.
c. Select
Change adapter settings
on the left of PC screen.
■ Right-click on your local adapter and select Properties.
■ In the Local Area Connection Properties menu, highlight Internet Protocol Version 4 (TCP/IPv4). Then, select the Properties button.
■ Select the radio button Use the following IP address and enter in the IP address for the PC (e.g., any IP address not in use, and in between 10.10.10.2
and 10.10.10.254), subnet mask (e.g., 255.255.255.0).
■ Select OK to change the PC’s IP address.
3. Power up the switch to be initially configured, and wait until it has finished its start-up processes.
4. Connect the PC to any 10/100/1000 RJ-45 Ethernet port on the switch using a standard Ethernet cable, and check the port LED on the switch to make sure
the link status of the PC is OK.
5. Run your web browser on the PC; enter either the DHCP-assigned or factory default IP address to access the switch’s web interface. If your PC is configured
correctly, you will see the login page of the switch requesting your username and password. In some browsers, the information needed may be requested in a
new window, or the switch may use a self-signed key/certification which requires the browser to warn of possible security issues. To continue connecting to
the switch, accept the security risk and proceed with the connection.
If you do not see the login page, perform the following steps:
a. Refresh the web page.
b. Check to see if there is an IP conflict issue.
c. Clean browser cookies and temporary Internet files.
d. Check your PC settings again and repeat Step 2.
6. Enter the factory default username in the login page. Select
Login
to log into the switch. .
Initial Switch Configuration Using CLI
The CLI can be accessed using the RJ-45 CONSOLE port available on the switch. To establish the connection to the console port, the following are needed:
■ PC with VT100 terminal emulation software
■ DB-9 to RJ-45 Serial Cable (the cable is provided along with the unit)
Complete the following steps:
NOTE
g
The factory default IP address of the switch is
10.10.10.1
and the subnet mask is
255.255.255.0
. If the switch is connected to a Dynamic Host
Control Protocol (DHCP) server, the server assigns the switch an IP address and the default
10.10.10.1
IP address is not configured. The DHCP
server also assigns your PC the correct IP address to allow a connection on the same subnet as the switch.
NOTE
g
Users can also skip Steps 1-2, by pressing
R
and typing the
ncpa.cpl
command to get to Step 4 directly.
NOTE
g
Be sure to record all your PC’s current IP settings to be able to restore them later.
NOTE
g
The factory default username of the switch is
admin
. The factory default password is
password
.
NOTE
g
There are many terminal emulation applications available on the web. PuTTy, Secure CRT, and HyperTerminal are a few examples.
