ADTRAN NetVanta 1224STR PWR Hardware Installation Manual Download Page 31

Page: 31 / 48

NetVanta 1224STR DC Hardware Installation Guide

Option Modules

61200590E1-34B

NetVanta ADSL NIM, Annex B (P/N 1202889E1)

The NetVanta ADSL NIM, Annex B (see

Figure 14

) adds ADSL capability to the NetVanta. See

Table A-11 on

page 47

for the pinouts. The ADSL NIM supports an optional DIM for dial backup applications. See

Table A-13

on page 48

for the DBU connector pinouts.

Figure 14. NetVanta ADSL NIM, Annex B

WAN-ADSL

DBU

Features and Specifications

ADSL Interface

•

ADSL over ISDN, Annex B

•

Supported Standards: ITU G.992.1
(G.dmt)

•

Connector: RJ-11C (6-pin jack,
inner pair)

ATM

•

Multiple Protocol over AAL5
(RFC 2684)

•

PPP over ATM (RFC 2364)

•

PPP over Ethernet (RFC 2516)

•

ATM Forum UNI 3.1/4.0 PVC

•

ATM Class of Service (UBR)

•

ATM F5 OAM

•

Up to 16 Virtual Circuits

Compliance

•

EMC - see

Electromagnetic

Compatibility (EMC) Table on page 6

•

AS/ACIF S043

•

EN 60950

•

IEC 60950

•

AS/NZS 60950

•

RoHS Compliant (Telecommunications
exemption)

Environmental

•

Operating Temperature: 0°C to 50°C

•

Storage Temperature: -20°C to 70°C

•

Relative Humidity: Up to 95 percent,
noncondensing

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

Summary of Contents for NetVanta 1224STR PWR














































Search results

Summary of Contents for NetVanta 1224STR PWR

Reviews:

Brands by name

Popular brands

ADTRAN NetVanta 1224STR PWR, Hardware Installation Manual

Search results

Summary of Contents for NetVanta 1224STR PWR

Reviews:

Brands by name

Popular brands