manualshive.com logo in svg

ADTRAN Express XRT, User Manual, Page: 95 / 111

Share
Download
ADTRAN Express XRT User Manual Download Page 95

Appendix C. Status Buffer Messages

61202.153L3-1

Express XRT User Guide

81

SERVICE_NOT_AVAIL

The requested service is not available.

SOURCE NOT ISDN

The incoming calling party is not ISDN (warning only). 

TANULL expired

Bonding timer TANULL expired.  Received call from non-BOND-
ING equipment.

TEMPORARY_FAILURE

The network has temporarily failed, try the call again.

TIMER_EXPIRY

Call control error.

TXADD01 expired

Bonding timer TXADD01 expired.

TXDEQ expired

B-channel delay equalization during bonding failed.

TXFA1 expired

Bonding timer TXFA1 expired.

TXFA2expired

Bonding timer TXFA2 expired.

TXINIT expired

Bonding timer TXINIT expired; called non-BONDING equip-
ment.

UNASSIGNED_NUMBER

The phone number dialed does not exist.

Unknown AT cmd

User issued an unknown AT command.

USER_ALERT_NO_ANS

Ringing call is not answered.

USER_BUSY

The dialed number is busy.

V120 connected

The V.120 rate adaption successfully connected to the far-end 
unit.

Summary of Contents for Express XRT
















































































































Reviews:

No comments