ADTRAN D4 U-BR1TE V Installation And Maintenance Manual Download Page 14

14

Section 61104020L4-5, Issue 3

61104020L4-5C

4. MAINTENANCE

The ADTRAN U-BR1TE V does not require routine
maintenance for normal operation.

5. WARRANTY AND CUSTOMER SERVICE

ADTRAN will replace or repair this product within ten
(10) years from the date of shipment if it does not meet
its published specifications or fails while in service.
Refer to ADTRAN 

U.S. and Canada Carrier Networks

Equipment Warranty, 

document 60000087-10.

Contact Customer and Product Service (CAPS) prior to
returning equipment to ADTRAN.

For service, CAPS requests, or further information,
contact one of the following numbers:

ADTRAN Sales

Pricing/Availability
(800) 827-0807

ADTRAN Technical Support

Pre-sales Applications/Post-sales Technical
Assistance
(800) 726-8663

Standard hours: Monday-Friday, 7 a.m. - 7 p.m. CST
Emergency hours: 7 days/week, 24 hours/day

ADTRAN Repair/CAPS

Return for Repair/Upgrade
(256) 963-8722

Repair and Return Address

ADTRAN, Inc.
CAPS Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807

Figure 13.  DS0 Latching Loopback

U-BR1TE V

2B

T1

T1

DS0 DP #1

SW 3

1 - LULT

2 - ADJ

SW 6

NORMAL

U-BR1TE

2B + D

T1

DSO DP #3

U-BR1TE (Non-ADTRAN)

DLC Application

NT 1

or

TA

CSU

NT 1

or

TA

CSU

U-BR1TE

2B + D

D4 Channel Bank

D4 Channel Bank

DS0 DP #1

DSO DP #2

COT

RT

T1

D4/SLC-96

RT

2B + D

or

2B

T1

DSO DP #3

SLC-96

NT 1

or

TA

CSU

LULT

LULT

2B

D4/SLC-96

COT

2B + D

or

2B

D4 Channel Bank

DS0 DP #1

DSO DP #2

U-BR1TE V

U-BR1TE V

U-BR1TE V

2B

SW 3

1 - LULT

2 - TANDEM

SW 6

NORMAL

SW 3

1 - LULT

2 - TANDEM

SW 6

NORMAL

SW 3

1 - LUNT

2 - TANDEM

SW 6

NORMAL

SW 3

1 - LULT

2 - ADJ

SW 6

NORMAL

LUNT

Summary of Contents for D4 U-BR1TE V















Reviews: