23
Accord xpC - July, 2001
3.
Alarm
This sets the output to 12 V switching to 0 V when any of the following occur:
•
Alarm Condition.
•
Panic Alarm.
•
Fire Alarm.
This output may be used to trip a transistorized relay for control of auxiliary equipment.
The alarm trigger can also be inverted so that it is normally 0 V switching to 12 V, see
Programming Group 5 Option 7 Trigger Output.
This option defaults to (1) 0V Detector Reset.
Table 3.10 Group 5 System Options
S
N
O
I
T
P
O
M
E
T
S
Y
S
P
U
O
R
G
N
O
I
T
P
O
T
L
U
A
F
E
D
5
.
)
s
e
Y
=
1
,
o
N
=
0
(
s
s
o
L
C
A
f
o
g
n
i
n
r
a
W
e
l
b
i
d
u
A
=
1
)
1
(
5
.
)
s
e
Y
=
1
,
o
N
=
0
(
y
r
t
n
E
y
r
a
t
n
e
m
e
l
p
p
u
S
=
2
)
0
(
5
.
s
m
r
a
l
A
r
o
f
t
e
s
e
R
r
e
e
n
i
g
n
E
=
3
.
)
e
r
o
t
s
i
n
h
c
e
T
r
o
r
e
e
n
i
g
n
E
=
3
,
e
r
o
t
s
i
n
h
c
e
T
=
2
,
r
e
e
n
i
g
n
E
=
1
,
r
e
m
o
t
s
u
C
=
0
(
)
3
(
5
.
)
s
e
Y
=
1
,
o
N
=
0
(
e
l
b
a
n
E
y
e
k
t
o
H
=
4
)
0
(
5
.
)
s
e
Y
=
1
,
o
N
=
0
(
d
a
p
y
e
K
t
i
m
O
o
t
u
A
=
5
)
0
(
5
.
)
d
e
v
o
m
e
R
.
g
e
N
=
1
,
d
e
i
l
p
p
A
.
g
e
N
=
0
(
t
u
p
t
u
O
l
l
e
B
=
6
)
0
(
5
.
)
d
e
v
o
m
e
R
.
g
e
N
=
1
,
d
e
i
l
p
p
A
.
g
e
N
=
0
(
t
u
p
t
u
O
r
e
g
g
i
r
T
=
7
)
0
(
5
.
s
r
e
p
m
a
T
y
a
D
r
o
f
t
e
s
e
R
r
e
e
n
i
g
n
E
=
8
.
)
e
r
o
t
s
i
n
h
c
e
T
r
o
r
e
e
n
i
g
n
E
=
3
,
e
r
o
t
s
i
n
h
c
e
T
=
2
,
r
e
e
n
i
g
n
E
=
1
,
r
e
m
o
t
s
u
C
=
0
(
)
0
(
5
.
)
.
L
.
O
.
E
=
2
,
d
e
c
n
a
l
a
B
e
l
b
u
o
D
=
1
,
p
o
o
L
C
/
N
=
0
(
n
o
i
t
a
r
u
g
i
f
n
o
C
e
n
o
Z
=
9
)
1
(
Group 4 — Option 8 Easy Set
When enabled (1) this option allows users to (Full, Part or Night) set the system without
entering a user code.
When enabled users set the system by pressing the # key and : 1 (to Full Set), 2 (to Part
Set), or 3 (to Night Set). The same exit times as apply as with Full, Part and Night Set. A
valid user code is still required to unset the system.
This option defaults to 0 (disabled).
System Programming — Group 5 System Options
Group five programming is as follows:
1.
The first digit entered is 5 for System Options.
2.
The second digit is the required system option 1 — 9.
3.
The third digit is the option value.
Group 4 — Option 9 Prevent Setting for Power Fails
This option determines which power fail conditions prevent setting of the system:
0.
Mains fail.
1.
Low battery.
2.
Mains fail and low battery.
This option defaults to 0 (mains fail).
Summary of Contents for ACCORD XPC
