ADS FlashLogic VWX Page 9 Product Manual Download

Page: 9 / 15

Patent No. US 8,856,780 CA 2759622

VWX Product Guide

MODULE RESET PROCEDURE - 1 OF 1

The following procedure resets the module

programming to the vehicle. It does not reset

any settings confi gured online.

Disconnect all connectors from module except

the M1 BLACK 8-pin connector and the M4

BLACK 20-pin connector.

Disconnect the M1 BLACK 8-pin connector

and the M4 BLACK 20-pin connector.

PRESS AND HOLD the module’s programming

button while connecting the M1 BLACK

8-pin connector and the M4 BLACK 20-pin

connector.

Wait, LED 1 will ﬂash RED. RELEASE

programming button.

LED 1 will turn RED for 2 seconds.

Module RESET completed.

Reconnect all connectors.

Repeat programming procedure.

Failure to follow procedure may result with a

DTC or a CHECK ENGINE error message.

www.idatalink.com

VWX

PAGE 9 OF 15

• 20220113

Summary of Contents for FlashLogic VWX
















Search results

Summary of Contents for FlashLogic VWX

Reviews:

Related manuals for FlashLogic VWX

Brands by name

Popular brands

ADS FlashLogic VWX, Product Manual

Search results

Summary of Contents for FlashLogic VWX

Reviews:

Related manuals for FlashLogic VWX

Brands by name

Popular brands