ADLINK Technology DLAP-8000 Series User Manual Download Page 39

Page: 39 / 103

System Layout

DLAP-8000

3.2.9

Extended PWR/RESET Header

An internal header is provided for the Power and Reset buttons,
with pin definition as shown.

Figure 3-18: PWR/RESET Header Pin Definition

Table 3-18: PWR/RESET Header Pin Definition

3.2.10

USIM Slot

The USIM slot connects to the Mini PCIe and M.2 slots.

3.2.11

12V Power for Additional AFM MXM Carrier Board

One 12V power pin header provides additional AFM MXM carrier
board power for an MXM card, if used.

Figure 3-19: 12V Power Pin Definition

Table 3-19: 12V Power Pin Definition

Pin

Signal

PWR_BTN-L

GND

RESET_BTN-L

Pin

Signal

Pin

Signal

P_+12V_B

GND

P_+12V_B

GND

NOTE:

For additional information regarding the AFM MXM Carrier
Board, please contact your ADLINK representative.

Summary of Contents for DLAP-8000 Series








































































































Search results

Summary of Contents for DLAP-8000 Series

Reviews:

Related manuals for DLAP-8000 Series

Brands by name

Popular brands

ADLINK Technology DLAP-8000 Series, User Manual

Search results

Summary of Contents for DLAP-8000 Series

Reviews:

Related manuals for DLAP-8000 Series

Brands by name

Popular brands