manualshive.com logo in svg

ADLINK Technology aTCA-3710, User Manual

Share
Download
ADLINK Technology aTCA-3710 User Manual Download Page 51

                                                 aTCA-3710 User's Guide

 

 
 

 51 

DIP Switches 

•

 

SW1:

 SW1 is used to switch between

 SPI flash boot

 and 

SD card boot

. The default setting is SPI 

flash boot. 

SW No. 

Mode 

Setting 

1 OFF 

2 ON 

3 ON 

SPI Flash 

4 OFF 

 

1 ON 

2 OFF 

3 OFF 

SW1 

SD Card 

4 ON 

 

Table 14. SPI Flash or SD Card Selection (SW1)

 

•

 

SW2: 

The front panel 

serial port

 is set to 

connect to the LMP console

 by default. For testing 

purposes, the serial port can be configured to connect to the 

IPMC console

 as shown in the 

following table. The baud rate is115200 for the LMP console and 9600 for the IPMC debug console. 

SW No. 

Mode 

Setting 

1 ON 

2 ON 

3 OFF 

LMP Console 

4 OFF 

 

1 OFF 

2 OFF 

3 ON 

SW2 

IPMC 

Debug Console 

4 ON 

 

Table 15. Faceplate Serial Port Selection (SW2) 

Summary of Contents for aTCA-3710






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands