manualshive.com logo in svg

ADJ WiFly Chameleon, User Instructions, Page: 8 / 18

Share
Download
ADJ WiFly Chameleon User Instructions Download Page 8

ADJ Products, LLC   -  www.adj.com  - WiFly Chameleon User Manual Page 7

life expectancy of the battery maybe shortened or the device 

in which the battery is used may be damaged by electrolyte 

gel leakage. If the batteries cannot maintain a charge for long 

periods of time, even when they are charged correctly, this may 

indicate it is time to change the battery.
6. Battery Disposal

Please dispose of battery according to local regulations.

  WiFly Chameleon                                Battery Precautions

ADJ Products, LLC  -  www.adj.com  - WiFly Chameleon User Manual Page 28

  WiFly Chameleon                          ADJ LED RC4 Operation  

  standard DMX controller. Please see pages 10-15 to for a detailed  

  descriptions of the DMX modes, values, and traits. 
• If the Red LED’s glow you are in 6 Channel Mode.

• If the Green LED’s glow you are in 7 Channel Mode.

• If the Blue LED’s glow you are in 9 Channel Mode.

• If the White LED’s glow you are in 11 Channel Mode.

• If the Amber LED’s glow you are in 18 Channel Mode.

• If the UV LED’s glow you are in 20 Channel Mode.

  WiFly Chameleon                      Battery Status & Recharge  

Battery Status:

This function is used to check the life status of the battery.

Plug the fixture in and press the MODE button until “BATT LEV 

XXX%”  is  displayed.  “XXX%”  represents  an  number  between 

“000” and “100”. The number that is displayed is the remaining 

battery life. If “BATT LEV ---” is displayed, it means the battery 

is dead or you are running the unit on AC power. Please do not 

let the battery fully die, this severly shortens the life of the 

battery.
Example:  If  “BATT  LEV  050%”  is  displayed,  the  battery  is  at 

half life. If “BATT LEV 025%” is displayed, the battery is at 25% 

life.

NOTE: After 20 seconds of inactivity, the display will revert 

back to the battery life display.
Battery Recharge: To recharge the battery, plug the supplied AC 

cord into the AC input on the side of the unit and plug the other 

end into a matching power supply. It will take about 3 hours to 

reach full charge. The display will STOP flashing when the unit 

reaches 100% charge. 

Note: When unplugging the unit from charging and then 

applying power via battery, there will be a minimal charge 

drop.
For a faster recharge, put the Load Switch in the “Off” position 

and the Battery Switch in the “ON” position.

Summary of Contents for WiFly Chameleon



















Reviews:

No comments