ADJ WiFly Chameleon User Instructions Download Page 6

ADJ Products, LLC   -  www.adj.com  - WiFly Chameleon User Manual Page 5

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Try to never short circuit the battery. It generates a very high 

current which could cause the battery to overheat which may 

result in electrolyte gel leakage, harmful fumes, or explosion. 

The LIR tabs may easily short-circuit by placing them on con-

ductive surface. A short circuit may lead to heat build up and 

damage of the battery. An appropriate circuitry with PCM is 

employed to protect accidental short circuit of the battery pack.
1.2 Mechanical shock

Droping the unit, impact hit, bending, etc. may cause failure or 

shortend life of the LIR battery.
3. Other

3.1 Battery connection

1). Direct soldering of wire leads or devices to the battery is 

strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to 

the batteries. Direct soldering may cause damage of compo-

nents, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the bat-

teries to provide extra safety protection. The battery pack is 

constructed in a way that no short circuit will occur which may 

cause smoke or fire.
3.3 Do No Disassemble the Batteries

1). Never disassemble the batteries.

Doing this may cause a internal short circuit in the battery, 

which may lead to harmful fumes, fire, explosion, or other prob-

lems.
2). Electrolyte Gel is harmful

Electrolyte Gel should not leak from the LIR battery. Should the 

electrolyte gel come into contact with the skin or eyes, flush the 

  WiFly Chameleon                                Battery Precautions

  WiFly Chameleon                               Dimmer Curve Chart

(Fade Time)

(Fade Time)

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

  WiFly Chameleon                                   Photometric Chart  

ADJ Products, LLC  -  www.adj.com  - WiFly Chameleon User Manual Page 30

Summary of Contents for WiFly Chameleon



















Reviews: