ADJ WiFly Chameleon User Instructions Download Page 1

User Instructions

 7/16

WiFly Chameleon

  WiFly Chameleon                                          Specifications 

  Model:  WiFly Chameleon

   Voltage:    

 

100V ~ 240V/50~60Hz 

  LEDs: 

 

 

3 x 18 Watt 6-in-1 LED’s 

  Beam Angle: 

 

15 Degrees

  Working Position:   

Any safe working position

   Power Consumption: 

57W

  Power Cord Daisy Chain: 12 Fixtures Max.

 

Fuse:   2 

Amp

   Weight:     

 

11lbs./ 5.1Kgs.

   Dimensions:  

 

10.25” (L) x 10.25” (W) x5” (H) / 7”  

 

 

   with 

kickstand 

extended

   

 

 

 

260 x 260 x 175mm

   Colors: 

 

 

RGBWA+UV Color Mixing

  DMX Channels:   

6 DMX Modes: 6 Channel Mode,   

   

 

 

 

7 Channel Mode, 9 Channel Mode,  

   

 

 

 

11 Channel Mode, 18 Channel 

   

 

 

 

Mode, & 20 Channel Mode  

  Warranty:                         2 Year (730 days)

Please Note: Specifications and improvements in the design of 

this unit and this manual are subject to change without any prior 

written notice.

Auto Sensing Voltage:

 This fixture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged 

into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

[email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Summary of Contents for WiFly Chameleon



















Reviews: