background image

  Inno Pocket Beam Q4                                          Cleaning

  Inno Pocket Beam Q4    

 

      Trouble Shooting

Trouble Shooting: Listed below are a few common problems that 

you may encounter, with solutions.
No light output from the unit;
1.  

Be sure the external fuse has not blown. The fuse is located on  

   the rear panel of the unit. 

2.   Be sure the fuse holder is completely and properly seated. 

 

Unit does not respond to sound;
1.     Low frequencies (bass) should cause the unit to react to sound.

    Tapping on the microphone, quiet or high pitched sounds may

   not activate the unit.  

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal  optical  lenses  and  mirror  should  be  carried  out  periodically  to 

optimize light output. Cleaning frequency depends on the environ-

ment  in  which  the  fixture  operates  (I.e.  smoke,  fog  residue,  dust, 

dew). In heavy club use we recommend cleaning on a monthly basis. 

Periodic cleaning will ensure longevity, and crisp output.
1.  Use normal glass cleaner and a soft cloth to wipe down the out- 

  side casing.

2.   Use a brush to wipe down the cooling vents and fan grill.

3.   Clean the external optics with glass cleaner and a soft  cloth every  

  20 days.

4.   Clean the internal optics with glass cleaner and a soft cloth every  

  30-60 days.

5.  Always be sure to dry all parts completely before plugging the unit  

  back in.

  Inno Pocket Beam Q4 

                              Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been 

removed  located  the  fuse  holder  located  inside  the  power  socket. 

Insert a flat-head screw driver into the power socket and gently pry 

out the fuse holder. Remove the bad fuse and replace with a new one. 

The fuse holder has a built-in socket for a spare fuse be sure not to 

confuse the spare fuse with active fuse.

ADJ Products, LLC  -  www.adj.com  - Inno Pocket Beam Q4 Instruction Manual Page 24

ADJ Products, LLC  -  www.adj.com  - Inno Pocket Beam Q4 Instruction Manual Page 25

 Inno Pocket Beam Q4   

           Dimmer Curve Chart

(Fade Time)

(Fade Time)

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

 Inno Pocket Beam Q4   

              Photometric Chart

1.0

2.0

3.0

4.0

Distance(m) 

0

0m(     ) 

W

5.0

4

B

G

R

(LUX)

6747                             5080                         2848                           1716                      1094                    

11320                           8930                          4764                           2866                      1613                     

610                               426.1                         223.8                          141.7                      93.7                     

16460                           12710                         6873                           4030                      2575                      

Diameter(m) 

0.07

0.14

0.21

0.279

0.349

RGBW

 20000                          12910                         6857                           4071                      2558                     

Summary of Contents for INNO POCKET BEAM Q4















Reviews: