background image

Please Note:

 Specifications and improvements in the design 

of this unit and this manual are subject to change without any 

prior written notice.

 Focus Spot Three Z                                      Specifications

Model:    

 

Focus Spot Three Z

Voltage: 

 

 

100 - 240V, 50/60Hz   

LED:   

 

 

1 x 100W Cold White LED

Power Consumption: 

230W

Dimensions:    7.25”(L) x 11.25”(W) x 19.75”(H)

 

 

 

 

183mm x 284mm x 489mm

Weight: 

 

 

26 Lbs. / 12 kgs.

Beam Angle:   

 

12-18 Degrees

Fuse:   

 

 

5 Amp

Power Cord Daisy Chain:  3 Fixtures Max. (120V)

 

 

 

 

6 Fixtures Max. (230V)

Duty Cycle:   

 

None

DMX:   

 

  

2 DMX Channel Modes: 18 Channel   

 

 

 

 

Mode & 21 Channel Mode

Sound Active:  Yes

Working  Position:   

Any Safe, Secure Position

Warranty: 

 

 

2 Year (730 days)

Auto Sensing Voltage:

 This fixture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged 

into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

[email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

ADJ Products, LLC  -  www.adj.com  - Focus Spot Three Z Instruction Manual Page 38

Summary of Contents for Focus Spot Three Z





















Reviews: