background image

 

 

 

 

 

BATTERY RECHARGER  

 

Be sure that the battery recharger is suitable for the installed 

batteries both for their capacities and type (lead/acid or GEL and 

equivalent). 

 

In the plastic bag containing the use and maintenance you will find the 

coupling connector for the recharger. It must be assembled onto the 

cables of your recharger, following the instructions given by the 

manufacturer. 

 

ON-BOARD BATTERY RECHARGER (OPTIONAL) 

If the machine is equipped with the on-board battery recharger (see 

under "OPTIONAL ACCESSORIES”) please refer to the instructions of the 

constructor of this accessory what the recharging operations concern.  

The battery recharger is connected directly to the battery poles. 

During the recharging operations a device is activated which does not 

permit the machine's functioning.  

The main cable of the battery recharger has a maximum length of two 

meters  (6.5 ft.) and must be connected to a single-phase socket type 

CEE 7/7. 

 

BATTERIES RECHARGING 

Bring the machine on a levelled surface. 

Plug in batteries connector (1) placed in the rear part of the machine, 

to connector (2) of the battery recharger. 

 

 

 

BATTERIES RECHARGING  WITH  ON-BOARD  BATTERY RECHARGER 

(OPTIONAL) 

 

Bring the machine on a leveled surface near to a single-phase socket 

(within 2m, 6.5 ft.) with tension 230V, frequency 50Hz (for USA 120V, 

60Hz), nominal current 10A. 

Switch off the switches of the brushes motor, suction motor and of the 

solenoid valve. 

Insert the plug into the mains socket. 

At the end of the recharging, take off the plug from the mains socket. 

 

 

 

 

Never charge a GEL battery with a non suitable recharger. Strictly 

follow the instructions supplied by the batteries and recharger 

manufacturer. 

In order not to cause permanent damages to the batteries, it is 

necessary to avoid their complete discharge, providing for the 

recharging within a few minutes after batteries discharge signal starts 

blinking. 

Never leave batteries completely discharged even if the machine is not 

used. In case of traditional batteries, please check the electrolyte level 

every 20 recharging cycles and eventually fill them up with distilled 

water. 

 

 

Danger of gas exhalations and emission of corrosive liquids. Fire 

danger: do not approach with free flames.

 

 

BATTERIES DISPOSAL 

It is compulsory to hand over exhausted  batteries, classified as 

dangerous waste, to an authorized institution according to the current 

laws. 

 

BATTERIES CHARGE LEVEL INDICATOR 

When the machine is switched on, on the display (1) appears the setting 

of the battery check card: 

GE 24: check card set for GEL batteries. 

Pb 24: check card set for lead batteries. 

 

 

 

On the display (1) the following indication of the battery charge level is 

digital and indicates the percentage of the battery charge. 100 is the 

maximum charge, down to a minimum of 10, indicating every 10% 

decrease. 

When the charge level reaches 10%, the  display starts blinking 

indicating the end of the battery charge. 

 

 

 

 

After a few seconds from the four blinking ‘’----’’ dashes, the brushes 

motor stops automatically. With the remaining charge it is anyhow 

possible to finish the drying operation before proceeding to the 

recharge. 

 

Summary of Contents for ruby 45t




















Reviews: