background image

 

Make maintenance regular part of daily operation. The daily maintenance routine needs to 

include 

 

-Cleaning of the machine and cleaning of all parts from residual wood debris. chips, dust, 

bark pieces and eventual other waster. 

-Greasing of the sliding pads inside the sliding casing(ram) 

-Hydraulic oil check and(in case of leakage)hydraulic hose and fittings check-up to detect 

eventual oil leaks 

-Lubrication of all moving parts 

 

5.2 Hydraulic oil 

 

Periodically check the oil level inside the hydraulic oil tank.  When doing so,  accurately 

avoid contaminating the tank with dirt, wood chips, sow dust etc… 

                             

Make sure that the splitter never runs without oil or with low oil level. When this happens, air 

is likely to reach inside the hydraulic loop. Failure to maintain due oil    or level may cause 

poor running and irregular splitter operation(very rough, back/forth or up/down motions)as 

well as major pump damages. 

 

Please schedule your first oil change after approximately 25-30 operation hours and later 

ones after each 50operation hours or once a year. 

 

The oil drain plug is location on the bottom tank side while the filler cap is on the upper right 

hand side of the tank. 

                                 

The hydraulic system is a closed system with oil tank, oil pump and control valve. Check oil 

level regularly in inspection glass. Low oil levels can damage the oil pump. Oil Level should 

measure approx.1—2cm lower than the upper surface of the oil tank. The oil should be 

completely changed once a year. 

 

 

Make sure moving parts stops and the log splitter is unplugged. 

 

Make sure that no dirt or debris finds its way into the oil tank. 

 

Collect used oil and responsibly recycle. 

 

Following an oil change, activate the log splitter a few times without actually splitting 

 

Recommended oil type; DEA HD B46,Shell Tell us 10-46,Esso Nuto H 46 

 

When changing the oil, never let used oil drop down on the ground. rather collect whole of it 

in a seated container for due disposal. Oil disposal container be of at least 8L capacity if 

you are using smaller container make sure to drain the more than one round to avoid 

splitting  old oil out on the ground.  Used oil is very polluting and should be disposed in 

accordance with local rules. 

 

After refilling the tank with new oil, let the splitter cycle three or four times and let the air 

blow out of the hydraulic loop before closing the cap. 

 

5.3 Ram sliding pads 

 

Should irregular noisy knocks be heard while ram is sliding up and down, grease the plastic 

sliding pads located inside the sliding ram casing.  Preferably use commercial grease 

available in your country. 

 

Make a trial test before starting to work again.  The noisy knock should disappear after  

greasing. 

 

Should you detect an unusually large gap between sliding ram casing and the guide, sliding 

pads are likely to be worn out. if so replace them with brand new ones. 

 

The actual splitting force may vary ±10% of the nominal rating 

 

 

Summary of Contents for VLS8TS-1


















Reviews: