background image

 
 
 
 

 

 

 

Wood clamping before splitting: 

 

3.7 Operation   

 

 

Firstly place the log on the working table and lean it against the log fixing device; 

 

Secondly press down the two operation handles to let the wedge run towards the log with 

wedge pressing on the top of the log. 

 

 

DO NOT RELEASE THE CONTROL LEVERS UNTIL THE CYCLE IS COMPLETELY 

OVER  AND THE  LOG  IS  SPLIT. 

 

Should any emergency arise and stopping be required, simply set the control levers free 

from your grip. When doing this, the ram will immediately travel all the way back up. 

As soon as the log is completely split, release both control levers and let the ram travel 

back to start position and be ready for a new cycle. 

Do not attempt to catch the split wood or remove wood sticks from the table by hand until 

the cylinder rod stops at its maximum travel position. 

Clear the table and remove chips and wood debris from the machine before starting a new 

cycle. 

 

When loading chunks, make sure that logs sits central and firmly with its saw end on the 

table. Never place your hands on top of the log when loading the log on the splitter. 

Do not split wood chunks with lots of branches,  first clean it and remove all branches 

DANGER, crooked trunk pieces with green/dry branches may burst under wedge pressure! 

Make sure to shut the motor off before leaving the area at work end. 

 

3.8 Clearing procedure 

 

Depending on the type or wood being split, along may not always break into two pieces and 

fall to the ground,  If a log sticks to the wedge,  place the valve handle in the neutral 

position(stop the wedge from traveling),switch the splitter off and carefully remove or 

hammer the log off the wedge. 

Allowing the log to remain attached to the wedge when it is fully retracted could lead to 

possible injury and/or damage to the log splitter. 

 

 

3.9 Pressure Limiting                  

 

Max pressure was set on the valve before log splitter is packed and leaves the factory. The 

setting was done by qualified person with professional tools. Unauthorized 

  resetting will cause possible problems for hydraulic system or result in damage to the 

machine   

 

 

 

 

4 Transport 

 

(1)

 

Turn on switch to start machine and press the two operation handles making piston rod 

going down closely to the square wood ,then turn off switch. 

 

 

 

Summary of Contents for VLS8TS-1


















Reviews: