–
11 –
*84 ASSIGN ZONE VOICE DESCRIPTORS
Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when the
system annouces any event involving a zone number. Press *84 while in programming mode. NOTE: Entry of a
number other than one specified will give unpredictable results.
ASSIGN ZONE VOICE DESCRIPTORS
0 = Exit mode, upon which this prompt blinks. Press [*] + any field number to go to that field.
1 = Enter mode
%
zz
ZONE NUMBER
Enter the 2-digit zone number (
zz) for which this descriptor is being assigned.
[*] = Continue to next prompt (existing descriptors will be announced, then descriptor 1 will be repeated.)
00 = Exit Zone Voice Descriptor mode (
displays blinking 84; enter
* +
desired data field or menu mode number
)
b
vv
DESCRIPTOR 1
Enter [#] + 2-digit vocabulary index number of first descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 2 (descriptor 2 will be announced)
8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
'
vv
DESCRIPTOR 2
Enter [#] + 2-digit vocabulary index number of second descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 3 (descriptor 3 will be announced)
8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
d
vv
DESCRIPTOR 3
Enter [#] + 2-digit vocabulary index number of third descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 or 8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
VOCABULARY INDEX
00
½ sec pause
A
01
ALARM
02
ATTIC
B
03
BABY
04 BACK
05
BASEMENT
06 BATHROOM
07
BEDROOM
C
08 CHECK
D
09 DEN
10 DETECTOR
11 DINING
12 DOOR
E
13 EMERGENCY
F
14
FIRE
15 FLOOR
16 FRONT
G
17 GARAGE
18 GUN
H
19 HALL
I
20 INSIDE
J
K
21
KITCHEN
L
22 LAUNDRY
23 LIBRARY
24 LIVING
M
25 MAIN
26 MASTER
27 MESSAGE
28 MOTION
O
29 OFFICE
P
30 PATIO
31 POOL
R
32 ROOM
S
33 SHED
34 SHOP
35 SIDE
36 SLIDING
37 SMOKE
38 STORAGE
39 SYSTEM
U
40 UPSTAIRS
41 UTILITY
W
42 WINDOW
Y
43 YARD
Z
44 ZONES
45 1
ST
46
2
ND
47
3
RD
70
Custom Word #1
71
Custom Word #2
72
Custom Word #3
73
Custom Word #4
74
Custom Word #5
99 Blank
(to erase previously
programmed word)
SYSTEM WORDS
(Announced by system
– not programmable)
AC LOSS
ARMED
AWAY
BYPASSED
CHIME
DISARMED
DISARM SYSTEM
NOW
EXIT NOW
FAULT
INSTANT
LOW BATTERY
NOT
READY TO ARM
STAY
*85 RECORD CUSTOM VOICE DESCRIPTORS
Use this mode to record up to 5 custom voice descriptors for use with zone announcements. Press *85 while in
programming mode. NOTE: Entry of a number other than one specified will give unpredictable results.
RECORD CUSTOM VOICE DESCRIPTORS
0 = Exit mode, upon which this prompt blinks. Press [*] + any field number to go to that field.
1 = Enter mode
%
7d
CUSTOM DESCRIPTOR NUMBER
Enter 7 +
d + [*], where d = 0-4, each representing custom word 70, 71, 72, 73 or 74 respectively.
Existing descriptor will be announced.
Press [#] to start recorder. Start speaking immediately after the third beep.
Speak the desired word clearly near the keypad microphone. Recording stops after 1.5 seconds.
6 = Accept word and ready to record next descriptor (prompt A….7d)
[#] = Re-record descriptor
00 = Exit Record mode after pressing 6
(displays blinking 85; enter * + desired data field or menu mode number)
Press any other key to repeat the recorded word.
