ADC HiGain HLU-200 User Manual Download

Page: 24 / 26

Product Support

350-200-115-02, Issue 2

September 25, 1998

HLU-200 List 1E

RODUCT

UPPORT

ADC Customer Service Group provides expert pre-sales and post-sales
support and training for all its products.

Technical support is available 24 hours a day, 7 days a week by contacting
the ADC Technical Assistance Center (TAC).

Sales Assistance

800.366.3891 extension 73000

(USA and Canada)

952.917.3000

Fax: 952.917.3237

•

Quotation Proposals

•

Ordering and Delivery

•

General Product Information

Systems Integration

800.366.3891, extension 73000
(USA and Canada)

952.917.3000

•

Complete Solutions (from concept to
installation)

•

Network Design and Integration Testing

•

System Turn-Up and Testing

•

Network Monitoring (upstream or downstream)

•

Power Monitoring and Remote Surveillance

•

Service/Maintenance Agreements

•

Systems Operation

ADC Technical Assistance Center

800.638.0031

714.730.3222

Fax: 714.730.2400

Email: [email protected]

•

Technical Information

•

System/Network Configuration

•

Product Specification and Application

•

Training (product-specific)

•

Installation and Operation Assistance

•

Troubleshooting and Repair/Field Assistance

Online Technical Support

•

www.adc.com/Knowledge_Base/index.jsp

Online Technical Publications

•

www.adc.com/library1/

Product Return Department

800.366.3891 ext. 73748 or

952.917.3748

Fax: 952.917.3237

Email: repair&[email protected]

•

ADC Return Material Authorization (RMA)
number and instructions must be obtained
before returning products.

All 800 lines are toll-free in the USA and Canada.

Summary of Contents for HiGain HLU-200



























Search results

Summary of Contents for HiGain HLU-200

Reviews:

Related manuals for HiGain HLU-200

Brands by name

Popular brands

ADC HiGain HLU-200, User Manual

Search results

Summary of Contents for HiGain HLU-200

Reviews:

Related manuals for HiGain HLU-200

Brands by name

Popular brands