ADC ES30/30 Installation & Operator'S Manual Download Page 3

Page: 3 / 24

112809 - 6

www.adclaundry.com

IMPORTANT

You must disconnect and lockout the electric supply and

the gas supply or the steam supply before any covers or

guards are removed from the machine to allow access for

cleaning, adjusting, installation, or testing of any equipment

per OSHA standards.
Please observe all safety precautions displayed on the

equipment and/or specified in the installation manual

included with the dryer.
Before installation, check that the local distribution

conditions, nature of gas and pressure, and adjustment of

the appliances are compatible.

CAUTION

Dryer(s) should never be left unattended while in operation.
“Caution: Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper

operation.”
«Attention: Au moment de l’entretien des commandes,

étiquetez tous les fils avant de les débrancher. Des erreurs

de câblage peuvent entraîner un fonctionnement inadéquat

et dangereux.»

WARNING

Children should not be allowed to play on or near the dryer(s).

Children should be supervised if near dryer(s) in operation.
Under no circumstances should the dryer door switch(es),

lint door/drawer switch(es), or heat safety circuit(s) ever

be disabled.
Do not modify this appliance.
The dryer must never be operated with any of the back

guards, outer tops, or service panels removed. Personal

injury or fire could result.
The dryer must never be operated without the lint filter/

screen in place, even if an external lint collection system is

used.

FOR YOUR SAFETY

Do not dry mop heads in the dryer. Do not use dryer in

the presence of dry cleaning fumes.

The dryers must not be installed or stored in an area where

it will be exposed to water and/or weather.
The wiring diagram for the dryer is located behind the control

panel.

List of Acronyms _______________________

HVAC

Heating, Ventilating, and Air-Conditioning

in WC

Inches of Water Column

L.C.D.

Liquid Crystal Display

L.P.

Liquid Propane

OSHA

Occupational Safety and Health Administration

R.M.A.

Return Material Authorization

Underwriters Laboratory

Proposition 65

Use of this product could expose you to substances

from fuel combustion that contain chemicals

known to the State of California to cause cancer,

birth defects and other reproductive harm.

Table of Contents ________________

In the State of Massachusetts, the following
installation instructions apply:

■

Installations and repairs must be performed
by a qualified or licensed contractor,
plumber, or gasfitter qualified or licensed by
the State of Massachusetts.

■

If using a ball valve, it shall be a T-handle
type.

■

A flexible gas connector, when used, must
not exceed 3 feet.

WARNING

Safety Precautions ..................................... 4
Specifications ............................................ 6
Installation Procedures .............................. 8

Service / Parts Information ..................... 20

Service ...................................................................... 20
Parts .......................................................................... 20

Warranty Information ............................... 20

Returning Warranty Cards .......................................... 20
Warranty .................................................................... 20
Returning Warranty Parts ........................................... 20

Routine Maintenance ............................... 21

Cleaning ..................................................................... 21
Adjustments ............................................................... 21

Data Label Information ............................ 22
Programming ............................................ 23

Summary of Contents for ES30/30

























Search results

Summary of Contents for ES30/30

Reviews:

Brands by name

Popular brands

ADC ES30/30, Installation & Operator'S Manual

Search results

Summary of Contents for ES30/30

Reviews:

Brands by name

Popular brands