ADB Signature Series Manual Download Page 9 | Manualshive

Page: 9 / 51

background image

L-852C-D ITCL Taxiway Centerline Inset Lights

Safety

©

2009 ADB Airfield Solutions, LLC.

96A0311F

Page 1-2

All rights reserved

Issued 3/05

WARNING

: Risk of electrical shock. Failure to observe this warning

may result in personal injury, death, or equipment damage.

WARNING

: Disconnect equipment from line voltage. Failure to

observe this warning may result in personal injury, death, or equipment
damage.

WARNING

: Wear safety goggles. Failure to observe may result in

serious injury.

CAUTION

: Failure to observe may result in equipment damage.

The term

qualified personnel

is defined here as individuals who thoroughly

understand the equipment and its safe operation, maintenance, and repair.
Qualified personnel are physically capable of performing the required tasks,
familiar with all relevant safety rules and regulations and have been trained to
safely install, operate, maintain, and repair the equipment. It is the responsibility
of the company operating this equipment to see that its personnel meet these
requirements.

WARNING

: Use of this equipment in ways other than described in

this manual may result in personal injury, death, or property and
equipment damage. Use this equipment only as described in this
manual.

2. Safety Symbols

(contd.)

3.

Qualified Personnel

4.

Intended Use

«
...
7
8
9
10
11
...
»

Summary of Contents for Signature Series




















































Reviews:

No comments

Related manuals for Signature Series

Brand: Valve Concepts Pages: 16

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: hager Pages: 62

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: tams elektronik Pages: 12

Brand: Maclaren Pages: 43

Brand: Lawler Pages: 5

Brand: Parker Pages: 54

Brand: RAM Pages: 71

Pearldex Series

Brand: KaMo Pages: 2

Brand: AMX Pages: 1

Brand: Whale Pages: 8

Brand: Tascam Pages: 8

Brand: Hearth Products Controls Pages: 5

Brand: Nustart Pages: 12

Brand: FAAC Pages: 10

SW-HBT4K-C6-4X4E

Brand: Avenview Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands