ADB Signature Series Manual Download Page 31 | Manualshive

Page: 31 / 51

background image

L-852C-D ITCL Taxiway Centerline Inset Lights

Troubleshooting

©

2007 Siemens Airfield Solutions

96A0311F

Page 5-3

All rights reserved

Issued 3/05

Moisture in lighting fixture

1. Open light assembly. Refer to

Opening

optical assembly

in the

Repair

section.

2. Check for cause of leakage (dirty or damaged

seal mating surfaces, defective seals, cracked
or broken prism, loose screws or damaged
wire insulation).

3. Clean, dry, inspect, or replace damaged

components.

5. Flashing LED

Incorrect current

Check the current to the fixture to ensure it is
within FAA specifications for the selected step.
If not, adjust the CCR or repair circuit issues.
Ensure that the isolation transformers have
adequate capacity to run the fixture, especially
if using arctic kit.

Underloaded CCR

For Thryristor controlled CCRs, ensure that the

CCR has a load at least 25% of maximum
output. If not, reduce the output taps to a
lower maximum voltage.

«
...
29
30
31
32
33
...
»

Summary of Contents for Signature Series




















































Reviews:

No comments

Related manuals for Signature Series

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Samson Pages: 20

Brand: Parkside Pages: 86

Brand: LLURIA Pages: 2

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Dickey-John Pages: 109

by-me Eikon 20526

Brand: Vimar Pages: 6

Home easy HE-440

Brand: CH Byron Pages: 2

Brand: RTI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands