manualshive.com logo in svg

ADB MIKADO, User Manual

Share
Download
ADB MIKADO User Manual Download Page 10

MIKADO USER MANUAL 

 

User Manual - page 8 

www.adblighting.com

 

Issue 1.0 
 

2. GETTING CONNECTED 

 

 
 
 
 
 

2.1 MAINS INPUT 

An IEC Mains Input socket is located on the rear panel and a mains power lead is provided. 
The MIKADO has an internal power supply that will operate on voltages between 190 volts 
and 260 volts AC with a frequency range from 47 to 63 HZ. 110-volt models are available 
direct from the factory. 
Plug the mains lead into the MAINS INPUT socket and connect it to a source of mains 
power. A Power Switch located next to the Mains Input connector allows you to switch the 
MIKADO off and on without removing the mains lead. The Mains Input socket is fused with a 
M205 sized 500mA fuse. 

 

2.2 DMX512 OUTPUT 

The MIKADO transmits a digital signal based on the DMX512/1990 standard. 
The output of the MIKADO is DMX512-A "ready". DMX-512A is an upgrade of the standard 
that is still under development. 
Connect a DMX512 data cable from the 5-pin XLR style connector on the rear panel to the 
DMX512 input of your equipment. Set the required DMX512 start address on your 
equipment. 
At this point, with the mains power and DMX512 connected, the MIKADO is ready to be 
operated. Simply switch on the "POWER" switch located near the Mains Input connector. 
The MIKADO will commence its start up procedure and will then commence operating in 
exactly the same state that it was in when it was last switched off. All the Memories and 
Chasers will be as they were. 
 

Hint; if you are starting a new lighting session, ADB recommends that you perform a 
"RESET" of the MIKADO. This will ERASE all previously recorded memories and will prevent 
you being confused by previous recordings and settings. If you need to keep your memories, 
save them to the optional plug-in memory module. 

 
You are now ready to start controlling your lights! 
For details on the COMMS PORT, AUDIO INPUT and EXT TRIG Input - refer Section 9 of 
this manual- "Utilities". 

Main input 
Fuse Holder 

Power 
Switch 

Audio 
 Input 

COMMS 
PORT 

DMX 512  
Output 

External 
Trigger input 

Summary of Contents for MIKADO





































Reviews:

No comments

Brands by name

Popular brands

Load more brands