Adaptive P1507 Maintenance Manual Download Page 7

Page: 7 / 44

Introduction

December 10, 2007

Front Access Full Matrix LED Sign Maintenance Manual (pn 1507610501 rev. A)

Introduction

Purpose

This manual is intended as a guide for maintenance and repairs considered field serviceable.

This field service manual supplies technical information for service and technical personnel so that they can
maintain the equipment at the assembly but not the component level.

Revision history

Related documentation

Technical documentation can be found at Adaptive’s Web site (http://www.adaptivedisplays.com).

Safety information

Equipment symbols

Warnings and cautions

Warnings and cautions are posted in appropriate locations throughout this manual.

Revision

Date

Notes

1507610501 rev. A

December 10, 2007

Initial release.

Part #

Manual title

Description

1507650207

Wiring Diagram

Sign wiring diagram for the 1.07-inch pitch sign
with two controllers.

1507650201

Wiring Diagram

Sign wiring diagram for the 1.35-inch pitch sign
with two controllers.

1507650202

Wiring Diagram

Sign wiring diagram for the 1.75-inch pitch sign
with two controllers.

TechMemo #00-0005

Preventing Electrostatic Discharge
(ESD) Damage

Describes the precautions to take to protect
electronic components from ESD damage.

Chassis ground

Summary of Contents for P1507













































Search results

Summary of Contents for P1507

Reviews:

Related manuals for P1507

Brands by name

Popular brands

Adaptive P1507, Maintenance Manual

Search results

Summary of Contents for P1507

Reviews:

Related manuals for P1507

Brands by name

Popular brands