background image

16

Federal Communications Commission Radio Frequency Interference Statement

WARNING: Changes or modifications to this unit not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy, and if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. However, if this equipment does 
cause interference to radio or television equipment reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is 

connected.

• Consult the dealer or an experienced radio/television technician for help.

Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this 
unit to the specified limits of the rules.

This device complies with part 15 of the FCC rules. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

Canadian Compliance Statement

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing 
Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matérial 
brouilleur du Canada.

Adaptec, Inc. 

USBConnect

Tested To Comply
With FCC Standards

FOR HOME OR OFFICE USE

Summary of Contents for USBConnect2000



























Reviews: