AcueLighting Profile LED 300 WW User Manual Download Page 4

Version 1.0 

 

DMX-512 connection/connection between fixtures 

 

Description of the XLR-connection: 

 

DM X OUT 

DM X IN 

 
 

 

1.

 

Ground 

2.

 

Signal (-) 

3.

 

Signal (+) 

1.

 

Ground 

2.

 

Signal (-) 

3.

 

Signal (+) 

 
 

 

If you are using a controller for operation, you can connect the DMX-output of the controller directly to the DMX-
input of the first fixture in the DMX-chain. If you wish to connect multiple fixtures to the same chain you may do 
so using the DMX output of the fixture. 

 

Building a serial DMX-chain: 

Connect  the  DMX-output  of  the  first  fixture  in  the  DMX-chain  with  the  DMX-input  of  the  next  fixture. 
Always connect one output with the input of the next fixture until all fixtures are connected. 

 

DMX-512 connection with DMX terminator: 

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as 
in a club or studio, it is recommended to use a DMX terminator. This helps in preventing interference of the digital 
control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120-ohm resistor connected 
between pins 2 and 3, which is then plugged into the DMX output socket of the last fixture in the chain. 

 

Caution: 

For the last fixture in the chain, the DMX-cable has to be terminated with a DMX terminator. Solder a 120 

resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture. 

 

Power connection: 

   Power Requirements: 

The  LED  Profile  300  WW  luminaire  operates  on  100  to  240  volts  AC  (+/-  10%,  auto-ranging).  This  luminaire   
contains an auto-switching power supply. 

 

Power linking between fixtures: 

The fixture has built in powercon in and out sockets. Connect the power out to the power in socket of the next fixture 
in the chain until all fixtures are connected. 

Caution: 

maximum power linking - 6 units. 

 

Connection with the mains: 

Connect the device to the mains with the enclosed powercon cable. 

 

The description of the powercon cable layout are as below: 

 

Cable color 

Connection 

International 

Brown/Black 

Live 

Blue/White 

Neutral 

Yellow/Green 

Earth(Ground) 

 

 

Summary of Contents for Profile LED 300 WW









Reviews: