background image

 

Pioneer Gripper 

 

 

Chapter 6 

Appendix A

 

S

TANDARD 

S

ERVER 

I

NFORMATION 

P

ACKET 

 

 

NAME

 

VALUE

 

DESCRIPTION

 

HEADER

 

int 

Exactly 0xFA, 0xFB 

BYTE COUNT

 

byte 

Number of data bytes + 2 (checksum), not including header or 
byte-count bytes 

STATUS

/

PACKET

 

0x3S = 

Motors status 

TYPE

 2 

Motors 

stopped 

 3 

Robot 

moving 

XPOS

 int 

Translation 

travel 

YPOS

 int 

 

 

THPOS

 Sint

 Orientation 

L VEL

 Sint 

Wheel 

velocities 

R VEL

 Sint 

 

BATTERY

 

byte 

Battery charge in tenths of volts (101 = 10.1 volts, for example) 

STALL AND

 

BUMPERS

 

int 

Motor stall and bumper indicators.  

CONTROL

 

Sint 

Setpoint of the server’s angular position servo 

FLAGS

 

Sint 

Various status and states. 

COMPASS

 

byte 

Electronic compass accessory heading in 2-degree units 

SONAR COUNT

 

byte 

Number of new sonar readings included in SIP 

       NUMBER

 

byte 

If Sonar Count>0, is sonar disc number 0-31; reading follows 

       RANGE

 

int 

Sonar range value; multiply by RangeConvFactor

 

REST OF THE SONAR READINGS

… 

GRIP

_

STATE

 

BYTE

 

Pioneer Gripper state byte 

ANPORT

 

BYTE

 

Selected analog port number 1-5 

ANALOG

 

BYTE

 

User Analog input (0-255=0-5 VDC)  reading on selected port 

DIGIN

 

BYTE

 

Byte-encoded User I/O digital input 

DIGOUT

 

BYTE

 

Byte-encoded User I/O digital output 

CHECKSUM

 

INTEGER

 Packet-integrity 

checksum 

 

15

Summary of Contents for Pioneer Gripper
























Reviews: