background image

www.acti.com

 
 

Hardware Manual 

                 

10 

Installation Procedures 

Preparing for Installation 

The following figures are for reference only. See the actual product for details. 

Before mounting the camera, check the device model, accessory types and quantities against 

the packing list to ensure the components are complete. 

 

Verify the bearing capacity of the mounted position 

Verify that the mounted position meets the bearing requirements. Otherwise, you are advised 

to reinforce the mounted position for the device weight. For more information, see the product 

datasheet. 

 

Verify the lightning protection and grounding requirements 

 

Select proper lightning protection devices for the power supply, audio and video signals 

interfaces, and RS485 interfaces. 

 

 

Cable Requirements 

10M/100M Ethernet CAT 5/5E UTP cables are applicable to the ANSI/EIA/TIA-568A/B and 

ISO/D. 

Eight wires in the network cable need to be inserted in parallel into the top of the cable 

connector. The cable connector needs to be crimped in position. When the cable connector is 

in position, ensure that the metal pieces of the cable connector are parallel to each other and 

the clamp of the cable connector is intact. 

 

Tail 

cable

Bracket 

adpater

Safety 

wire

Dome

Summary of Contents for Z950

















Reviews: