background image

www.acti.com

 
 

Hardware Manual 

                 

Cautions

 

 

Make sure the power supply voltage is correct before using the camera. 

 

Do not drop the camera or subject it to physical shock. 

 

Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth 

with a bit of ethanol and wipe it gently. If the camera will not be used for an extended 

period, please replace the lens cap to protect the sensor from dirt.   

 

Do not aim the camera at the sun or extra bright places. Blooming or smearing may 

occur otherwise (which is not a malfunction), and affect the endurance of sensor at the 

same time. 

 

The sensor may be burned out by a laser beam, so when any laser equipment is in 

using, make sure that the surface of sensor will not be exposed to the laser beam. 

 

Do not place the camera in extremely hot, cold (the operating temperature shall be-30° 

C to +60° C, or -40° C to +60° C if the camera model has an "H" in its suffix), dusty or 

damp locations, and do not expose it to high electromagnetic radiation.   

 

To avoid heat accumulation, good ventilation is required for operating environment.   

 

Keep the camera away from liquid while in use. 

 

While in delivery, the camera shall be packed in its original packing, or packing of the 

same texture. 

 

Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment 

shall be replaced regularly according to their average enduring time. The average time 

varies because of differences between operating environment and using history, so 

regular checking is recommended for all the users. Please contact with your dealer for 

more details. 

 

Improper use or replacement of the battery may result in hazard of explosion. Replace 

with the same or equivalent type only. Dispose of used batteries according to the 

instructions provided by the battery manufacturer.   

 

If the product does not work properly, please contact your dealer or the nearest service 

center. Never attempt to disassemble the camera yourself. (We shall not assume any 

responsibility for problems caused by unauthorized repair or maintenance.) 

 

 

 

Summary of Contents for Z76



























Reviews: