background image

www.acti.com

 
 

Hardware Manual 

                 

Precautions 

Read these instructions 

You should read all the safety and operating instructions before using this product. 

 

Heed all warnings 

You must adhere to all the warnings on the product and in the instruction manual. Failure to 

follow the safety instruction given may directly endanger people, cause damage to the system 

or to other equipment.   

 

Servicing   

Do  not  attempt  to  service  this  video  device  yourself  as  opening  or  removing  covers  may 

expose  you  to  dangerous  voltage  or  other  hazards.  Refer  all  servicing  to  qualified  service 

personnel.

 

 

Trademarks 

All names used in this manual are probably registered trademarks of respective companies.   

 

Liability 

Every reasonable care has been  taken during  the  writing  of this manual.  Please  inform your 

local office if you find any inaccuracies or omissions. We cannot be held responsible for any 

typographical  or  technical  errors  and  reserve  the  right  to  make  changes  to  the  product  and 

manuals without prior notice.   

 

 

 

Summary of Contents for E44A








































Reviews: