background image

          

 

Product Name 

EK-AI7931LD

 

Version 

Doc No 

912-13802 

Date 

2022/11/14 

Page 

24  / 26 

PRODUCT USER GUIDE 

www.acsip.com.tw

 

5.

 

Federal Communication Commission Interference 
Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one of the following measures: 
 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Caution:

  Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to operate this equipment. 
 

This device complies with Part 15 of the FCC Rules. Operation is subject to the   
following two conditions: (1) This device may not cause harmful interference, and (2)   
this device must accept any interference received, including interference that may   
cause undesired operation. 

 

IMPORTANT NOTE: 
FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 20cm between 
the radiator & your body. 
This transmitter must not be co-located or operating in conjunction with any other antenna or 
transmitter. 
Country Code selection feature to be disabled for products marketed to the US/CANA 

Pro

vid

ed 

by 

AcS

ip 

Pro

vid

ed 

by 

AcS

ip 

Pro

vid

ed 

by 

AcS

ip

Summary of Contents for EK-AI7931LD



































Reviews: