background image

 

2.0.   Fingerprint Scanner 

BioCARDKey is built around the TouchChip Silicon fingerprint sensor. It is a fast, reliable and 
inexpensive fingerprint peripheral, which can be used to authenticate users of computers and all kinds 
of information technology devices. 

The TouchChip device is suitable for applications such as desktop access control, network security, 
Internet-based applications and commercial verification and identification systems. It contains all the 
necessary biometric components: fingerprint sensing, image optimization and matching. Application 
Programming Interface (API) is also provided for easy integration into applications and to save a lot of 
development time.  (Please refer to Programmer’s Guide for more information on API.)  

TouchChip active capacitive sensing provides a much higher immunity to parasitic effects leading to a 
higher signal-to-noise ratio and the ability to capture a wider range of fingerprints than competing 
technologies, such as passive capacitive sensing. 

Typically there are two processes involved in a biometric application: 

1. Enrollment: 

 

Before the identity of an individual can be verified via his/her fingerprints, it is necessary to 
capture one or several fingerprint samples. This process is called enrollment. The samples 
are referred to as fingerprint templates and can be stored on a broad range of media such as 
computer storage devices or smart cards. 

2. Verification:

  

The verification process requires a user to verify his identity by placing his finger on the 
fingerprint scanner sensor. The live fingerprint is compared with a stored template using a 
matching algorithm in order to determine whether they represent the same set of fingerprints. 
The matching result is then made available to the computer. 

When using the fingerprint device, the security level is mainly governed by two parameters: 

1.  False Acceptance Rate (FAR):

  

FAR is the probability that a false sample matches with the original template previously 
extracted from the subject’s fingerprint images during enrollment. 

2.  False Rejection Rate (FRR):

  

FRR is the rate at which the system incorrectly rejects a legitimate attempt to verify.  

 

Document Title Here 

Document Title Here 

Document Title Here

 

AET60 Reference Manual 

Version 1.7  

 

Page 4 of 24

 

[email protected] 

www.acs.com.hk 

Summary of Contents for AET60 BioCARDKey

























Reviews: