ACR Electronics : 2846.0 Product Support Manual Download | Manualshive

Page: 41 / 44

background image

Y1-03-0233 Rev. L

40

APPENDIX I - WARRANTY, NOTICES

1.

Limited Warranty

This product is warranted against factory defects in material and workmanship for
a period of 1 (one) year* from date of purchase or receipt as a gift. During the
warranty period ACR Electronics, Inc. will repair or, at its option, replace the unit

at  no  cost  to  you  for  labor,  materials  and  return  transportation  from  ACR.  For
further  assistance,  please  contact  our  Technical  Service  Department  at  ACR
Electronics,  Inc.,  5757  Ravenswood  Road,  Fort  Lauderdale,  FL  33312-6645.
Email: [email protected], Fax: +1 (954) 983-5087, Telephone: +1 (954) 981-
3333.

This  warranty  does  not  apply  if  the  product  has  been  damaged  by  accident  or
misuse,  or  as  a  result  of  service  or  modification  performed  by  an  unauthorized
factory.  Except  as  otherwise  expressly  stated  in  the  previous  paragraph,  THE
COMPANY  MAKES  NO  REPRESENTATION  OR  WARRANTY  OF  ANY  KIND,
EXPRESS  OR  IMPLIED,  AS  TO  MERCHANTABILITY,  FITNESS  FOR  A
PARTICULAR  PURPOSE,  OR  ANY  OTHER  MATTER  WITH  RESPECT  TO
THIS  PRODUCT.  The  Company  shall  not  be  liable  for  consequential  or  special
damages.

To place the warranty in effect, register online at

www.acrartex.com

or return the

attached card within 10 days.

*Five years for the following products: EPIRB, PLB, S-VDR, SSAS.

2.

Notices

ACR  Electronics  diligently  works  to  provide  a  high  quality  Product  Support
Manual,  however,  despite  best  efforts,  information  is  subject  to  change  without
notice, and omissions and inaccuracies are possible. ACR cannot accept liability
for  manual  contents.  To  ensure  that  you  have  the  most  recent  version  of  the
Product Support Manual, please visit the ACR website at

www.acrartex.com

©2009  by  ACR  Electronics,  Inc.  All  rights  reserved.  Reproduction  in  whole  or in
part is permitted only with permission of ACR Electronics, Inc.

Ongoing  product  improvements  may  change  product  specifications  without
notice.

Trademarks or registered trademarks are the property of their respective owners.

«
...
39
40
41
42
43
...
»

Summary of Contents for : 2846.0













































Reviews:

No comments

Related manuals for : 2846.0

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands