ACR Electronics : 2846.0 Product Support Manual Download | Manualshive

Page: 23 / 44

background image

Y1-03-0233 Rev. L

22

Always  refer  battery  replacement  and  any  other  beacon  service  to  a
factory  authorized  Service  Center.  Find  a  Center  near  you  at
http://www.acrartex.com.  Battery  replacement  includes  servicing  the
beacon  by  replacing  all  o-rings,  testing  the  water  seal  and  the  electrical
properties and doing a full functional test on the unit.

NOTE:

There are no user serviceable items inside the beacon. Do not

open the beacon except to disable (in case of faulty or accidental
activation). Otherwise, always have the beacon serviced.

WARNING: Battery contains lithium

To  avoid  possible  fire,  explosion,  leakage  or  burn  hazard,  do  not  open,
recharge,  disassemble  or  heat  beacon  above  +70ºC  (+158ºF)  or
incinerate.

These  products  contain  lithium  in  the  battery.  Various  beacons  may  or
may  not require special shipping instructions due to the lithium batteries
and  changes  in  shipping  regulations.

Shipping of hazardous materials

requires special handling and documentation. MSDS sheets, along with
shipping

information,

can

be

found

on

our

website

at

http://www.acrartex.com.

In the  case  of  the  RLB-36,  the  product  contains  small  batteries  that  are
non-hazardous.  However,  regulations  can  change.  Be  advised  that  it  is
best to verify the shipping requirements at the time you are preparing to
ship the unit.

4.

Shore based maintenance for SOLAS vessels, (SBM) IMO

MSC/Circ. 1039

The Maritime Safety Committee has approved guidelines for shore-based
maintenance  of  satellite  beacons,  for  the  purpose  of  establishing
standardized  procedures  and  minimum  levels  of  service  for  the  testing
and maintenance of satellite beacons. The first shore based maintenance
on  all  ACR  EPIRBs  is  due  at  the  date  of  the  first  battery  replacement.
Visit ACR’s  website at

www.acrartex.com

for organizations that perform

shore based maintenance.

5.

Annual testing for SOLAS vessels, IMO MSC/Circ. 1040

SOLAS  regulation  IV/15.9  dictates  annual  testing  of  406  MHz  satellite
EPIRBs.  Testing  should  be  carried  out  using  suitable  test  equipment
capable of performing the relevant measurements. All checks of electrical
parameters should be performed in the self-test mode, if possible. These
tests  can  be  performed  by  certified  ACR  Battery  Replacement  Centers
(BRCs).

Visit ACR’s website at

www.acrartex.com

for authorized ACR

BRCs.

«
...
21
22
23
24
25
...
»

Summary of Contents for : 2846.0













































Reviews:

No comments

Related manuals for : 2846.0

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands