ACR Electronics : 2846.0 Product Support Manual Download | Manualshive

Page: 34 / 44

background image

Y1-03-0233 Rev. L

33

APPENDIX D - USER INTERFACE: DIGITAL DISPLAY
DURING SELF-TEST

The following chart describes the display and audio-visual feedback the
beacon provides during Self-Test. The messages on the digital display
typically appear as one or two words at a time, until the entire message has
been displayed.

GlobalFix™ iPRO Display, LED/ Audio Signaling and Description of Operation

Beacon Self-

Test has been initiated, and the ACR Electronics’ Welcome Page appears.

Next, the product name page appears.

The first test checks the available hours of battery life (battery witness seal). If remaining
battery life is greater than 48 hours at -20° C, the test passes.

The first test checks the available hours of battery life (battery witness seal). If remaining
battery life is less than 48 hours at -20° C, the test fails.

The second test checks the beacon message for absence of errors

(EEPROM memory). If no errors are present the test passes.

The second test checks the beacon message for absence of errors (EEPROM memory). If
an error(s) is present, the test fails.

The third test checks circuit board (lock circuit)

functionality. If the board is performing properly, the board passes.

The third test checks circuit board (lock circuit) functionality. If the board is not performing
properly, the board fails.

BATT

>

48HR

√

beep

BATT >

48HR



beep beep

MEM

√

beep

MEM



beep beep

BOARD

TEST

√

beep

BOARD

TEST



beep beep

G

R

G

R

G

R

«
...
32
33
34
35
36
...
»

Summary of Contents for : 2846.0













































Reviews:

No comments

Related manuals for : 2846.0

Brand: Philips Pages: 2

Brand: Mustang Survival Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands