Figure 1
1. Input voltage is AC12V. The lamps must be connected with transformer.
2. The junc�on box is located at least 1200mm from the edge of the pool.
3. The moun�ng bracket must be properly installed so that the top edge of the
light’s lens is at least 450mm below the water level in the pool. see Figure 1.
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
5.
If the cable connec�on is done underwater, the connec�on part must be
waterproof protected
(use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
6.
Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
7.
Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
8. There are 3 wires for RGB with remote control.
Connec�ng the signal wire out of water, enhancing the ability of signal receiving.
9. It is easy to replace the lamp.
Signal wire
AC Power wire
AV power wire
MINI 1200mm
250mm
Rigid conduit
Junc�on Box
Water Level
Mini. from bo�om of
J.B. to water level
From water level to top of lens
Wall surface
Pool body
450mm
300mm
INSTALLATION
RGB Working Mode
15 Color Programs(For RGB ON/OFF )
No.1
Blue
Red
Green
Red/Blue
Blue/Green Red/Green White
Red-Red/Grn-Grn
Grn-Grn/Blu-Blue
Same as program 11, the speed is slower.
Cycle Red-Grn-Blu,Speed from fast to low.
Gradual change of all colors.
Gradual change of Red-Grn-Blu.
Grn-Red/Blu-Blu-Red-White-Blu/Grn-Red/Grn
Red-Red/Blu-Blue
No.2
No.3
No.4
No.5
No.6
No.7
No.8
No.9
No.10
No.11
No.12
No.13
No.14
No.15
2
3
Open Posi�on
Lock Posi�on
FIXTURE
MOUNTING
SCREW
FIXTURE TAB
SLOT
SCREW LOCATION
CONDUIT
7CM FROM
CENTER
TOP
FIXTURE
MOUNTING
SCREW
FIXTURE TAB
SLOT
SCREW LOCATION
CONDUIT
7CM FROM
CENTER
TOP
3
2
Figure 1
1. Input voltage is AC12V. The lamps must be connected with transformer.
2. The junc�on box is located at least 1200mm from the edge of the pool.
3. The moun�ng bracket must be properly installed so that the top edge of the
light’s lens is at least 450mm below the water level in the pool. see Figure 1.
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
5.
If the cable connec�on is done underwater, the connec�on part must be
waterproof protected
(use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
6.
Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
7.
Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
8. It is easy to replace the lamp.
MINI 1200mm
250mm
Rigid conduit
Junc�on Box
Water Level
Mini. from bo�om of
J.B. to water level
From water level to top of lens
Wall surface
Pool body
450mm
300mm
DIMENSION
INSTALLATION
180mm
38mm
Posición libre
Posición bloqueada
FIXTURE
MOUNTING
SCREW
FIXTURE TAB
SLOT
SCREW LOCATION
CONDUIT
7CM FROM
CENTER
TOP
3
2
Figure 1
1. Input voltage is AC12V. The lamps must be connected with transformer.
2. The junc�on box is located at least 1200mm from the edge of the pool.
3. The moun�ng bracket must be properly installed so that the top edge of the
light’s lens is at least 450mm below the water level in the pool. see Figure 1.
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
5.
If the cable connec�on is done underwater, the connec�on part must be
waterproof protected
(use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
6.
Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
7.
Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
8. It is easy to replace the lamp.
MINI 1200mm
250mm
Rigid conduit
Junc�on Box
Water Level
Mini. from bo�om of
J.B. to water level
From water level to top of lens
Wall surface
Pool body
450mm
300mm
DIMENSION
INSTALLATION
180mm
38mm
Posición libre
Posición bloqueada
