manualshive.com logo in svg

ACP OMNISTIM 500 PRO, User Manual, Page: 38 / 44

Share
Download
ACP OMNISTIM 500 PRO User Manual Download Page 38

- 34 -

 

 

  OMNISTIM

®

 500 PRO USER MANUAL 

 

 

COPYRIGHT © 2004 - 2018, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVED 

 

LEAD WIRE TESTER OPERATION 

 

Lead Wires should be inspected periodically, as well as any time there are output anomalies reported by the patient. 

•

 

Plug the distal (patient end) of the lead wire into the test connectors while observing polarity (red / black). 

•

 

Plug the device end of the lead wire into the receptacle labeled LEAD WIRE TESTER. 

•

 

When the POWER is on, green LED will turn on if the lead wire passes the test.  LED will be red if the 

lead wires are faulty and need to be replaced. 

•

 

When lead wires pass the test, check for loose connections by holding the lead wire about 3 inches from 

plug-in connectors and slowly rotate the lead wire in a circular motion while the wires are plugged in.  If 

the indicator LED is flickering between red to green, the lead wire should be replaced. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 7 

 

 

UNIT OUTPUT TEST 

 

When testing a unit for output, the output tester should be used on a constant output protocol. 

•

 

Power unit ON. 

•

 

Insert output tester into channel A. 

•

 

Select Pain / IFC Sensory. 

•

 

Increase the output level to 20mA on channel A. 

•

 

Observe the output tester LED. 

–

 

If the output tester has a solid, brightly lit LED, then 

there is sufficient output present on the selected 

channel. 

•

 

Change the output tester to channel B and follow the above 

process. 

 

 

Service Center 

 

For repair or service of ACP Products and accessories, please call (800) 350-1100 and follow the prompts.  Normal 

hours of operation are 6:00am to 5:00pm Pacific  Standard Time. After hours, please leave a message and a 

technician will return your call during the next scheduled workday. 

 

Patient-end of lead 

wire, Red-coded 

Patient-end of lead 

wire, Black-coded 

Device-end of 

lead wire 

LED lights green when lead 

wire is functional, and lights 

red when lead wire needs 

to be replaced. 

Summary of Contents for OMNISTIM 500 PRO













































Reviews:

No comments