manualshive.com logo in svg

ACP OMNISTIM 500 PRO, User Manual, Page: 22 / 44

Share
Download
ACP OMNISTIM 500 PRO User Manual Download Page 22

- 18 -

 

 

  OMNISTIM

®

 500 PRO USER MANUAL 

 

 

COPYRIGHT © 2004 - 2018, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVED 

 

OMNISTIM

®

 

500 PRO PROGRAM MENU 

 

Pain Control 

 

The following protocols are found by pressing the PAIN protocol button.  The first protocol displayed is IFC 

SENSORY.  Other protocols follow, in the sequence presented below, by continuously pressing the PAIN button. 

 

  A.   IFC SENSORY: 

Provides symptomatic relief of superficial and deep pain from localized dermatome or segmental origin.  

Bilateral, bipolar or quadripolar application through the painful area or over the involved spinal segments.  

Apply parallel to incision line for post op pain management.  Set intensity to illicit a pleasant tingling 

sensation, just below muscle contraction.  Sensory stimulation activates A-beta fibers causing the release of 

spinal Enkephalin and Dynorphin to block pain at the segmental level (Gate Control).  Duration of relief is 

typically from 30 minutes to 2 hours.  Fast onset of relief is usually within 15-20 minutes. 

 

 

USER ADJUSTABLE 

PARAMETER (Y/N) 

ORDER IN 

PARAMETER 

SET LOOP 

PARAMETER NAME 

ADJUSTABLE 

RANGE (UNIT) 

DEFAULT 

(UNIT) 

N 

 

CARRIER FREQ 

 

5.0 (kHz) 

N 

 

BURST FREQUENCY 

 

100 (Hz) 

N 

 

BURST RATE SCAN 

 

20 (%) 

N 

 

RATE SCAN 

 

ON 

N 

 

RATE SCAN TIME 

 

20 (s) 

Y 

2 

VECTOR 

Slow 45,  Fast 45, 

Slow 90, Fast 90, OFF 

Fast 90 

Y 

1 

TREATMENT TIME 

0…99 (min) 

15 (min) 

 

  B.   TENS-LVPC SENSORY: 

This program provides symptomatic relief of superficial pain from localized dermatome or segmental 

origin.  Bilateral, bipolar application through the painful area or over the involved spinal segments.  Apply 

parallel to incision line for post op pain management.  Set intensity to illicit a pleasant tingling sensation, 

just below muscle contraction.  Sensory stimulation activates A-beta fibers causing the release of spinal 

Enkephalin and Dynorphin to block pain at the segmental level (Gate Control).  Duration of relief is 

typically from 30 minutes to 2 hours.  Fast onset of relief is usually within 15-20 minutes. 

 

USER ADJUSTABLE 

PARAMETER (Y/N) 

ORDER IN 

PARAMETER 

SET LOOP 

PARAMETER NAME 

ADJUSTABLE 

RANGE (UNIT) 

DEFAULT 

(UNIT) 

Y 

2 

PHASE DURATION 

40…300 (μs)

 

80 (μs)

 

Y 

3 

PULSE RATE 

0.0…250 (Hz) 

100 (Hz) 

N 

 

PHASE DURATION MOD 

 

20 (%) 

N 

 

MODULATION 

 

OFF 

N 

 

RATE SCAN TIME 

 

4 (s) 

Y 

1 

TREATMENT TIME 

0…99 (min) 

15 (min) 

N 

 

CHANNEL MODE 

 

A/B SIM. 

                         

 

 

Summary of Contents for OMNISTIM 500 PRO













































Reviews:

No comments