background image

 

 

Table of Contents 

1. GENERAL INFORMATION  ............................................................................... 2 

1-1. Introduction and Description....................................................................................... 2 

1-2. Owner Assistance ........................................................................................................ 2 

1-3. Equipment Supplied and  Options ............................................................................... 2 

1-4 Features ........................................................................................................................ 3 

1-5 Safety Considerations, Explicit Definitions ................................................................... 3 

2. INSTALLATION.................................................................................................. 4 

2-1. Unpacking and Initial Inspection................................................................................... 4 

2-2. Preparing of the system units....................................................................................... 4 

2-3. Mounting of the rack option ........................................................................................ 4 

2-4. Connections ................................................................................................................ 4 

3. OPERATION ....................................................................................................... 7 

4. MAINTENANCE ................................................................................................. 7 

4-1. Cleaning ..................................................................................................................................... 7 

4-2. The ACOM3x2000A Simplified Schematic Diagram.................................................................. 8 

4-3. Troubleshooting.........................................................................................................................

5. SPECIFICATIONS............................................................................................... 8 

6. STORAGE AND SHIPMENT

..................................................................................... 8 

 

 

 

 

 

 

 

 

 

 
 
 

Summary of Contents for 3x2000A










Reviews: