background image

 
 

POWER

 

  On 

Power On

 

3. Button: 

MENU 

  To select the programming functions 

DOWN 

  To go backward in the selected functions 

UP 

  To go forward in the selected functions 

ENTER 

  To confirm the selected functions 

4. Dimmer Adjust knob: 

Adjusts the lightness for the unit; 

5. DMX OUT: 

DMX 512 link, use a 3/5-pin XLR cable to link to the next unit; 

6. DMX IN 

DMX 512 link, use a 3/5-pin XLR cable to link the unit to a DMX controller; 

7. POWER OUT: 

Connects to the next unit; 

8. POWER IN: 

Connects to mains supply power. 

 

3.2 Main Function   

To select any of the given functions, press the 

MENU

 button up to the required selection as shown 

on the  display. Select the function with  the 

ENTER

  button and the display will blink. Use the 

DOWN

/

UP

 buttons to change the mode. Once the required mode has been selected, press the 

ENTER

 button to confirm. To go back to the main functions without any changes press the

 MENU

 

button again. Press and hold the 

MENU

 button for about one second or wait for 7 seconds to exit 

the current mode. 

The main functions are shown below: 

 

Summary of Contents for LITE PANEL 900 LP-900 CW BD30

















Reviews: