background image

Page 5 / 26

 

DTUS066 rev A1 March 21, 2012 

 
 

Regulatory information / Disclaimers 

 

Installation  and  use  of  this  Wireless  LAN  device  must  be  in  strict  accordance 
with  the  instructions  included  in  the  user  documentation  provided  with  the 
product.  Any  changes  or  modifications  (including  the  antennas)  made  to  this 
device that are not expressly approved by the manufacturer may void the user’s 
authority to operate the equipment. The manufacturer is not responsible for any 
radio  or  television  interference  caused  by  unauthorized  modification  of  this 
device,  or  the  substitution  of  the  connecting  cables  and  equipment  other  than 
manufacturer  specified.  It  is  the  responsibility  of  the  user  to  correct  any 
interference  caused  by  such  unauthorized  modification,  substitution  or 
attachment.  Manufacturer  and  any  authorized  resellers  or  distributors  will 
assume  no  liability  for  any  damage  or  violation  of  government  regulations 
arising from failing to comply with these guidelines. 
 
Information  in  this  document  is  subject  to  change without  notice  and  does  not 
represent a commitment on the part of ACKSYS. 
 
ACKSYS  provides  this  document  “as  is”,  without  warranty  of  any  kind,  either 
expressed or implied, including, but not limited to, its particular purpose.  
 
ACKSYS  reserves  the  right  to  make  improvements  and/or  changes  to  this 
manual, or to the products and/or the programs described in this manual, at any 
time. 
 
Information provided in this manual is intended to be accurate and reliable.  
 
However,  ACKSYS  assumes  no  responsibility  for  its  use,  or  for  any 
infringements on the rights of third parties that may result from its use. 
 
This  product  might  include  unintentional  technical  or  typographical  errors. 
Changes are periodically made  to the information herein to correct such  errors 
and these changes are incorporated in new editions of the publication. 
 

Summary of Contents for WLn-LINK-OEM-RJ




























Reviews: