-1-
3
4
9
a) Illustration above shows exploded view
components for plow blade parts.
a) Place each slide hinge on blade and align
edge of hinge with factory mark on blade.
b) When both hinges are properly aligned -
they should measure 22-1/2 inches apart.
c) Turn bottom half of blade over and set it on wood blocks, one at
each end as shown. Take top half and connect tongue and groove
joint with bottom half. Slide sections until flush at both ends.
c) At end of blade, insert two square nuts in each
channel - flat side facing out. Slide nuts over to
hinge and align them with holes at top and
bottom.
Bottom section
of aluminum
blade
Slide Hinge
Top
section of
aluminum
blade
Blade Marker
Box End
Rubber Blade
Use 2x4 to prop
bottom of blade up
at both ends
Tongue
and
groove
joint
Align edge
with factory
mark
Align square nut
here at top
Align square nut here at bottom
End Plate
Slide Hinge
Align this edge of each slide
hinge with factory mark
Factory marks
on blade
22
1
⁄
2
” apart
a) Attach rubber end and metal cap plate to end
of blade with four long self threading bolts.
b) Tighten all bolts until rubber begins to com-
press to blade.
c) Tighten all bolts equally. Repeat box end
assembly at opposite end.
OPERATION INSTRUCTIONS
ANGLED INTERCEPTOR NOTE: THERE ARE TWO HOLES IN THE INTERCEPTOR SHAFT. WHEN INSERTING ANGLE INTERCEPTOR INTO FRONT MOUNT
RECEIVER, SELECT THE HOLE WHICH ALLOWS BLADE TO SWING ITS FULL ANGLE WITHOUT CONTACTING VEHICLE.
OPERATORS NOTE: WHEN PUSHING SNOW ONTO A PILE, ALWAYS DO SO WITH BLADE IN THE
STRAIGHT FORWARD POSITION. PILING SNOW WITH BLADE ANGLED MAY CAUSE DAMAGE
TO PLOW OR VEHICLE COMPONENTS.
Long self
threading
bolts (4)
Metal end cap
Rubber box end
1. TO LOWER FOR PUSHING SNOW:
Step behind blade and remove keyhole pin. Lift one side of blade out of retainer until slide hinge fits over the push bar, then lower blade
to ground. Re-insert keyhole pin. Repeat same procedure for other side of blade.
2. TO PUSH SNOW:
Drive forward slowly - blade will engage for pushing. When push is finished, backing up disengages the
blade until you are realigned for next push. Repeat this procedure until job is finished.
3. TO STORE BLADE FOR TRANSPORTING:
Reverse procedure from step 1 and re-insert keyhole pins.
4. TO STORE BLADE DURING OFF SEASON:
For maximum blade life, periodically retighten bolts and protect blade from sun by storing it inside or
covering.
22
1
⁄
2
”
RECEIVER
CLEARANCE
8”-16”
PUSH FRAME CLEARANCE
8”-10”
Tip: apply soapy
water solution to
parts for easier
assembly.
b) Align end of rubber edge with
matching channel in bottom sec-
tion of aluminum blade and slide
in until flush at both ends.
5
6
7
8
-2-
b) Make sure slide hinge is lined up with mark
(see Step 3). Using 9/16” wrench,
tighten hex
bolts in top section first. Then tighten hex
bolts on bottom section.
a) Turn 3/8 x 3/4” hex bolts with flat washer into
nuts on top section of blade
and leave loose.
Turn 3/8 x 3/4” hex bolts into nuts on bottom
section of blade
and leave loose.
c) Using 5/16” bit, drill a hole through blade in
each factory punched hole on slide hinge. Turn
a (short) 3/8” self threading bolt into each
drilled out hole and tighten. Repeat steps to
attach opposite slide hinge.
Drill 5/16” hole
in blade
Factory
hole in
slide
hinge
Bottom hex
head bolt
w/flat
washer
Top hex head bolt w/flat
washer (loose for now)
b) Using a 9/16” wrench turn a (short) 3/8” self
threading bolt into 5/16” pilot hole and tighten.
Repeat at other end.
a) At tongue-n-groove joint, drill a 5/16” pilot hole
at factory mark in v-groove at each end of
blade.
c) Using torque wrench, tighten all (6) bolts on
each slide hinge to 31 ft./lbs.
*
Torque bolts to 31 ft./lb.
*
*
*
*
**
Drill 5/16” hole at
factory mark (1 at
each end)
Tighten these
bolts second
Tighten these
bolts first
a) At bottom of blade (where rubber is inserted, check to make sure
ends are flush), then drill a 3/16 inch pilot hole at factory mark in
v-groove (4 locations) – drill only through 1st layer of aluminum and
into rubber. Repeat this drilling procedure for three remaining marks.
b) Using Phillips #3 bit, run a self drilling screw into each of the
four pilot holes. This prevents rubber from movement.
Ends flush
Factory
mark
(4x)
3/16 drill bit
#3 Phillips
self drilling
screw
a) Hang blade on push frame in the transport
position and insert key hole pins.
b) Insert two square nuts into top channel.
Turn a hex nut onto stud of blade marker
and align marker with hole on lift handle
and bolt marker and handle to blade using
square nut in channel.
c) Turn 3/8 x 3/4 bolt into other hole on handle
and thread to nut in channel. Handle should
be flush with blade edge. Then tighten both
bolts on lift handle. Repeat at other end.
Keyhole Pin
Slide
Hinge
Blade
Marker
Hex Head
Jamb Nut
2 square nuts
in channel
flat side up
3/8” self
threading bolt
