8”-10”
8”-10”
2
-3-
Tools Needed (plow assembly):
NOTE: Prior to plow assembly, park vehicle
on level grade and install plow mount
receiver (instructions with receiver).
Clearance under receiver should measure
between 8 to 16 inches above grade.
b) Check push frame for vertical
plumb. If plumb, tighten 4 bolts
now and go to step 3. If not plumb
- refer to shim procedure at right.
c) If push frame leans
towards front of vehicle,
shim at top pair of bolts.
If push frame leans away
from front of vehicle, shim at
bottom pair of bolts.
WHEN SHIMMING IS COMPLETE - TIGHTEN ALL 4 BOLTS.
BUBBLE
PLUMB
SHIM HERE
SHIM
HERE
a) With bolts snug tight, level push frame
horizontally.
a) Insert interceptor into receiver - leg up.
Secure with pins (interceptor has choice of
holes to allow for clearance when angling
blade). Hold push frame against interceptor.
Select 4 bolt hole pattern that positions
push
frame 8” – 10” above grade. If lowest bolt
pattern is too high, remove interceptor and
turn leg down. Bolt push frame (4 bolts 1/2 X
3-1/2 w/lock nuts) to proper hole height on
interceptor -
leave bolts snug tight for now.
b) Push set collar tight against receiv-
er - hold and tighten set screw with
3/16 allen wrench.
PUSH
FRAME
4 BOLTS
1/2 X 3-1/2,
AND LOCK
NUTS
INTERCEPTOR CAN BE INSTALLED WITH LEG TURNED UP OR DOWN AS NEEDED
FOR PROPER PUSH FRAME CLEARANCE (SHOWN TURNED UP IN ILLUSTRATIONS).
PUSH FRAME CLEARANCE
8”-10”
RECEIVER
CLEARANCE
8”-16”
Square Nut
#10172
Hitch Pin w/R-Pin
#10597
Set Collar
#50616
3/8 x 2-1/2” Self
Threading Bolt
#30502
Front Mount
Varies By Vehicle
Model
Rubber Box End
#50522
Keyhole Push
Frame #30479
Rubber Blade
#40730
#14 Ph. Hd. Self Drilling
Screw #10914
3/8” Self Threading Bolt
#10893
Keyhole Pin
#30489
1/2 x 3-1/2” Bolt #30512
With Lock Nut #20534
Leveling Shim #10591
Swivel Pin #20608
Interceptor Angle
#30604
3/8” Self
Threading Bolt
#10893
3/8 x 3/4” Bolt
#10185 With Flat
Washer #10185
Flat Washer
#10185
Lift Handle
#10573
Slide Hinge
#60291
3/8 x 3/4” Bolt
#10183
Blade Marker Kit
#40685
3/8 x 3/4” Bolt
#10183
Metal End
Plate
#50514
1
Parts Diagram
Ft./lb. torque wrench
Impact or ratchet with 9/16 and 3/4 socket
Drill with 3/16 and 5/16 drill bit
#3 Phillips driver bit
Box wrench 3/4
Open wrench 5/16
Allen wrench 3/16
2 short pcs. of 2 x 4 blocking
Bubble level
Protective eyewear
8”-10”
8”-10”
2
-3-
Tools Needed (plow assembly):
NOTE: Prior to plow assembly, park vehicle
on level grade and install plow mount
receiver (instructions with receiver).
Clearance under receiver should measure
between 8 to 16 inches above grade.
b) Check push frame for vertical
plumb. If plumb, tighten 4 bolts
now and go to step 3. If not plumb
- refer to shim procedure at right.
c) If push frame leans
towards front of vehicle,
shim at top pair of bolts.
If push frame leans away
from front of vehicle, shim at
bottom pair of bolts.
WHEN SHIMMING IS COMPLETE - TIGHTEN ALL 4 BOLTS.
BUBBLE
PLUMB
SHIM HERE
SHIM
HERE
a) With bolts snug tight, level push frame
horizontally.
a) Insert interceptor into receiver - leg up.
Secure with pins (interceptor has choice of
holes to allow for clearance when angling
blade). Hold push frame against interceptor.
Select 4 bolt hole pattern that positions
push
frame 8” – 10” above grade. If lowest bolt
pattern is too high, remove interceptor and
turn leg down. Bolt push frame (4 bolts 1/2 X
3-1/2 w/lock nuts) to proper hole height on
interceptor -
leave bolts snug tight for now.
b) Push set collar tight against receiv-
er - hold and tighten set screw with
3/16 allen wrench.
PUSH
FRAME
4 BOLTS
1/2 X 3-1/2,
AND LOCK
NUTS
INTERCEPTOR CAN BE INSTALLED WITH LEG TURNED UP OR DOWN AS NEEDED
FOR PROPER PUSH FRAME CLEARANCE (SHOWN TURNED UP IN ILLUSTRATIONS).
PUSH FRAME CLEARANCE
8”-10”
RECEIVER
CLEARANCE
8”-16”
Square Nut
#10172
Hitch Pin w/R-Pin
#10597
Set Collar
#50616
3/8 x 2-1/2” Self
Threading Bolt
#30502
Front Mount
Varies By Vehicle
Model
Rubber Box End
#50522
Keyhole Push
Frame #30479
Rubber Blade
#40730
#14 Ph. Hd. Self Drilling
Screw #10914
3/8” Self Threading Bolt
#10893
Keyhole Pin
#30489
1/2 x 3-1/2” Bolt #30512
With Lock Nut #20534
Leveling Shim #10591
Swivel Pin #20608
Interceptor Angle
#30604
3/8” Self
Threading Bolt
#10893
3/8 x 3/4” Bolt
#10185 With Flat
Washer #10185
Flat Washer
#10185
Lift Handle
#10573
Slide Hinge
#60291
3/8 x 3/4” Bolt
#10183
Blade Marker Kit
#40685
3/8 x 3/4” Bolt
#10183
Metal End
Plate
#50514
1
Parts Diagram
Ft./lb. torque wrench
Impact or ratchet with 9/16 and 3/4 socket
Drill with 3/16 and 5/16 drill bit
#3 Phillips driver bit
Box wrench 3/4
Open wrench 5/16
Allen wrench 3/16
2 short pcs. of 2 x 4 blocking
Bubble level
Protective eyewear
